- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- HP BL20p G3 Blade server ILO
ProLiant Servers - Netservers
1753288
Members
5430
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-02-2006 01:28 PM
тАО05-02-2006 01:28 PM
HP BL20p G3 Blade server ILO
When I log into my HP Rack Blade servers through the ILO on the first blade the last 3 blades report wrong ip address. I can ping the configured address but cannot access the ilo ports. Is there a way to reset these to default and acquire a dhcp address? This ilo interface seems hosed.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2006 03:44 AM
тАО05-03-2006 03:44 AM
Re: HP BL20p G3 Blade server ILO
Use front Port, From POST (Use keyboard & Monitor)
F8 for ILO - Reset Defaults
Default DHCP enabled
or from ILO diagnostic PORT 192.168.1.1
Under Administration - Network Settings
F8 for ILO - Reset Defaults
Default DHCP enabled
or from ILO diagnostic PORT 192.168.1.1
Under Administration - Network Settings
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-04-2006 09:43 PM
тАО05-04-2006 09:43 PM
Re: HP BL20p G3 Blade server ILO
I had a similar problem on one of the BL25p's I just installed on a customer site. I tried resetting the iLO config as shown in the above post, as well as resetting the nvram of the blade all to no avail. In the end it turned out to be a H/W fault with the iLO board (which is built into the mother board) so had to have it swapped out by an HP engineer.
Hopefully your problem will be solved by a reset.
Julian.
P.S. Are they all using the latest iLO firmware?
Hopefully your problem will be solved by a reset.
Julian.
P.S. Are they all using the latest iLO firmware?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP