- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- HP GBE2C Issues
ProLiant Servers - Netservers
1753384
Members
5843
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-02-2009 07:12 AM
03-02-2009 07:12 AM
HP GBE2C Issues
We have a C-3000 enclosure with a GBE2C interconnect switch installed. I have been trying to get the management side of the switch working through OA and managed to lock myself out of the BBI interface, what I did was enable & configure if256 and gw4 and applied settings as well as configured EBIPA and ended up being unable to log back into the switch. There was a management URL present but I could not login (would time out) -- I followed the directions at bladeconnect.com but I guess I didn't really know what I was doing.
So I then connected to the switch via null modem cable and did:
boot/conf
factory
save
reset
The switch reset yet the configured values I had put into it are still there. So I walked through the CLI and removed & disabled if256 and gw4 and again saved, rebooted.
I still cannot login to the switch via BBI but what I'd really like to do is make the management URL work from OA the way it was designed but I admit I'm pretty lost on this because I'm not entirely sure what's going on.
Is there a way to really reset back to factory? Losing all my changes and bring it back to the state of when I first pulled it out of the box? I can settle for not getting it working via OA but I'd really like to get the BBI working again.
So I then connected to the switch via null modem cable and did:
boot/conf
factory
save
reset
The switch reset yet the configured values I had put into it are still there. So I walked through the CLI and removed & disabled if256 and gw4 and again saved, rebooted.
I still cannot login to the switch via BBI but what I'd really like to do is make the management URL work from OA the way it was designed but I admit I'm pretty lost on this because I'm not entirely sure what's going on.
Is there a way to really reset back to factory? Losing all my changes and bring it back to the state of when I first pulled it out of the box? I can settle for not getting it working via OA but I'd really like to get the BBI working again.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP