- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: HP TC4100 server not finding SCSi windows 2003
ProLiant Servers - Netservers
1752303
Members
4509
Online
108786
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
Not applicable
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-27-2007 10:37 PM
01-27-2007 10:37 PM
HP TC4100 server not finding SCSi windows 2003
Hello all,
I have Recently bought a a TC4100 for use and i cannot get it to find the SCSI in the windows installation. I have try giving the installation different driver with no luck. I have also got the SCSI chip code and got the drivers from the LSI website but these give an error and so do the ones within the windows setup so it will not find the controller.
the system specs are this:
2x 1.13ghz P3
1Gb HP ECC RAM (2x512Mb)
4x 18.2Gb seagate SCSI Hard Drives (all are found in the boot up of the SCSI card)
can anyone shed any light on this.
Thank You
I have Recently bought a a TC4100 for use and i cannot get it to find the SCSI in the windows installation. I have try giving the installation different driver with no luck. I have also got the SCSI chip code and got the drivers from the LSI website but these give an error and so do the ones within the windows setup so it will not find the controller.
the system specs are this:
2x 1.13ghz P3
1Gb HP ECC RAM (2x512Mb)
4x 18.2Gb seagate SCSI Hard Drives (all are found in the boot up of the SCSI card)
can anyone shed any light on this.
Thank You
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-10-2007 10:29 AM
03-10-2007 10:29 AM
Re: HP TC4100 server not finding SCSi windows 2003
Darren,
I am not sure if you are using the on-board SCSI controller or an HP NetRAID RAID controller. Either way, you should get your drivers from HP's support website, not LSI, even though LSI may make the actual chipset/controller.
Hope this helps.
I am not sure if you are using the on-board SCSI controller or an HP NetRAID RAID controller. Either way, you should get your drivers from HP's support website, not LSI, even though LSI may make the actual chipset/controller.
Hope this helps.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP