- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- ML150, 6-port SATA RAID, Win SBS 2003, cannot dete...
ProLiant Servers - Netservers
1748204
Members
4086
Online
108759
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
11-06-2005 08:27 PM
11-06-2005 08:27 PM
ML150, 6-port SATA RAID, Win SBS 2003, cannot detect disks
I have a ML150 G2, model 366357-421, with (HP) 6-port SATA RAID controller and 2 160GB SATA disks.
I'm trying to install Windows SBS 2003, but it says it cannot find any disks to install on.
I have tried to supply the following drivers at setup (F6) of OS:
HP6-port_SATA_RAID_Controller_Driver_for_Windows_v4.2.1.7365
HPEmbedded_SATA_RAID_Controller_Driver_for_Windows_v5.2.3790.0
aac4.2.0.7344-2
but no luck.
I don't know what to try next, any ideas?
I'm trying to install Windows SBS 2003, but it says it cannot find any disks to install on.
I have tried to supply the following drivers at setup (F6) of OS:
HP6-port_SATA_RAID_Controller_Driver_for_Windows_v4.2.1.7365
HPEmbedded_SATA_RAID_Controller_Driver_for_Windows_v5.2.3790.0
aac4.2.0.7344-2
but no luck.
I don't know what to try next, any ideas?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-09-2006 10:29 AM
02-09-2006 10:29 AM
Re: ML150, 6-port SATA RAID, Win SBS 2003, cannot detect disks
I had no problem. I created the floppy following the instructions. The drives were visable after the SBS installation.
If you are intending to use the disks in a Raid 1 configuration, you need to configure the raid array before the installation. In that case, you need to go into the controller during post and create the array.
When you install SBS, put the floppy in when requested. The Raid-1 disk will be seen.
If you are intending to use the disks in a Raid 1 configuration, you need to configure the raid array before the installation. In that case, you need to go into the controller during post and create the array.
When you install SBS, put the floppy in when requested. The Raid-1 disk will be seen.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP