- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: ML370 Event ID: 9 Error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2004 03:51 AM
тАО01-07-2004 03:51 AM
ML370 Event ID: 9 Error
Relatively new cables throughout.
Any assistance is appreciated.
Patrick G.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2004 05:00 AM
тАО01-07-2004 05:00 AM
Re: ML370 Event ID: 9 Error
Check out www.eventid.net. Enter the Event ID and the source to see if there are any solutions. You can also try searching on a search engine such as www.google.com for event ID 9 and the source to find solutions elsewhere on the internet.
But, here is the general MS knowledge base article on troubleshooting Event IDs 9 & 11:
http://support.microsoft.com/?kbid=314093
Basically, the error could be caused by a large variety of issues: firmware versions, hardware problems (termination, controller, cable, drives) or driver problems.
So, to troubleshoot this issue:
--check for proper termination on the SCSI chain (both internal and external devices)
--make sure you have the latest drivers and firmware for all the devices on the chain
--check the SCSI chain for any physical problems (bent pins, damaged cables, loose connections, etc.)
--for tape devices, make sure the SCSI transfer rate of the controller matches the recommended transfer rate of the tape device, you may have to slow the controller down
--check for media errors on hard drives and tape drives
I hope this helps. Good luck!
Alicia
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2004 06:22 AM
тАО01-07-2004 06:22 AM
Re: ML370 Event ID: 9 Error
1. What Microsoft Spk version do you have installed? Spk3? Spk4?
2. Do need to verify the actual driver version installed for cpqarry2.sys, and the driver for the other SmartArray controller.
3. If the 4314R storage device is (temporarily) disconnected, does this eliminate the Event ID 9 error being logged?
Alicia is on the right track - for Windows 2000 Event ID 9 & 11 documentation see Q154690 (referenced on the URL given by Alicia).
Keep us posted!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2004 08:12 AM
тАО01-07-2004 08:12 AM
Re: ML370 Event ID: 9 Error
1. I am running SP4
2. cpqarry2.sys - v5.14.0.0 10/21/02
5300 driver - cpqcissm.sys v5.46.2.32 4/30/03
The server has locked up twice now since the rebuild. I have run the array diag. utility and both passed. I ran the Compaq Windows Diag Utility in quick test mode with no errors. I am going to kick off the complete test before I leave tonight.
I am not really sure if this cpqarry2 error is tied to the lockup as it was 19 hours between the cpqarry2 error and the actual lockup, but there were no other system events between that error and the "previous system shutdown was unexpected" error at reboot.
One other odd thing. The drive light that is usually always on on the front of the Compaq hot swap drives (next to the arrow access light) is always off on all of the drives connected to the 431.
I will have to arrange a time to disconnect the 4314R to test if the message goes away.
Thank you both very much for your responses.
Patrick G.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-25-2004 01:14 PM
тАО03-25-2004 01:14 PM
Re: ML370 Event ID: 9 Error
Brad C.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-17-2005 07:29 AM
тАО05-17-2005 07:29 AM