- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Netserver E 60
ProLiant Servers - Netservers
1753263
Members
5083
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2006 08:44 AM
тАО01-03-2006 08:44 AM
Netserver E 60
I have an old Netserver E 60 I'm trying to load NT 4.0 Server on. I downloaded a NetRAID driver from HP (two in fact,drv_nt_nr_all_409.exe and drv_nt_nr_all_405.exe) and tried them both on install, and NT still says no disks found.
The netRAID utility shows both drives and the one logical disk.
Any ideas what is going wrong?
Thank you.
The netRAID utility shows both drives and the one logical disk.
Any ideas what is going wrong?
Thank you.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-05-2006 12:57 PM
тАО01-05-2006 12:57 PM
Re: Netserver E 60
Dan,
Your almost there...
When you boot on a clean install, Windows should give you an opportunity to install a specific driver (usually by pressing the F6 key). You will need to insert a floppy disk drive with this driver. You may need to get this driver from HP's website and you may need to create the disk drive from the download.
This driver should recognize the NetRAID controller and see the logical disk.
Let me know how it goes...
DR
Your almost there...
When you boot on a clean install, Windows should give you an opportunity to install a specific driver (usually by pressing the F6 key). You will need to insert a floppy disk drive with this driver. You may need to get this driver from HP's website and you may need to create the disk drive from the download.
This driver should recognize the NetRAID controller and see the logical disk.
Let me know how it goes...
DR
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2006 04:05 AM
тАО01-06-2006 04:05 AM
Re: Netserver E 60
That's basically what I'm doing, you press "s" to specify a device, put in the disk with the HP drivers, it comes up with the NetRaid controller, I know it sees it because if you try to use another one, it says- you do not have this installed, but then it says it can't find any disk drives.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP