- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: No Graphic signal output when install Role as...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-03-2019 10:01 AM - edited тАО05-03-2019 10:40 AM
тАО05-03-2019 10:01 AM - edited тАО05-03-2019 10:40 AM
No Graphic signal output when install Role as AD and promo to DC
Hello, somebody can help me.
gen10 installed w2012r2. it goes well. MS office and Teamviewer is runing fine on the server.
Then I added a role as AD and promo to DC. it shows all going well.
system hint restart. after it restart. NO Graphic signal output.
I can see it on line on Teamviewer from remote computer.
i try to establish session by teamviewer. but password is not long valid.
Force restart, BIOS is runing fine. and cound not find any error.
when press boot for windows. it displays nothing on monitor. Monitor show no signal.
what did I lose for configuration or wrong setup during DCPROMO?
I am afraid of that even I reinstall OS. the problem still come if the cause not get.
tks n brgds
Liu Wei
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-04-2019 04:26 AM
тАО05-04-2019 04:26 AM
Re: No Graphic signal output when install Role as AD and promo to DC
I am the same issue T-T
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-07-2019 07:14 AM
тАО05-07-2019 07:14 AM
Re: No Graphic signal output when install Role as AD and promo to DC
Hello
Please have a look at below links to troubleshoot DC issue
Request you to engage the OS vendor for further support if you have a support agreement for the same
Disclaimer
NOTE:One or more of the links above will take you out side the Hewlett Packard Enterprise Website, Hewlett Packard Enterprise does not control and is not responsible for information out side of the Hewlett Packard Enterprise Website.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-08-2019 06:35 AM
тАО05-08-2019 06:35 AM
Re: No Graphic signal output when install Role as AD and promo to DC
It seems to be a problem with AMD graphics drivers, not the 2012R2 OS. After I uninstalled the AMD graphics driver, I can display it normally after using the MS basic driver. I am requesting a new version of the AMD graphics driver. . .