- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Proliant 1600 - Rebuild Issue
ProLiant Servers - Netservers
1748122
Members
3573
Online
108758
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-13-2006 06:54 PM
тАО01-13-2006 06:54 PM
Proliant 1600 - Rebuild Issue
Hi There,
The Proliant is running a smart array 221 controller.
Ran System Erase for a clean slate - installed System Configuration Utility from floppies and went to try and load the Array Configuration Utility however the Smartstart CD won't boot.
As a result, no disks are being recognised.
The only ACU I can find on smart start 5.5 is for windows only, not boot time.
Does anyone know of an ACU for the 221 that can be run at boot time?
I've tried two from the HP site, however they require NT drivers to operate and fail when they go to search for the controller.
Appreciate any assistance.
Regards,
Iain
The Proliant is running a smart array 221 controller.
Ran System Erase for a clean slate - installed System Configuration Utility from floppies and went to try and load the Array Configuration Utility however the Smartstart CD won't boot.
As a result, no disks are being recognised.
The only ACU I can find on smart start 5.5 is for windows only, not boot time.
Does anyone know of an ACU for the 221 that can be run at boot time?
I've tried two from the HP site, however they require NT drivers to operate and fail when they go to search for the controller.
Appreciate any assistance.
Regards,
Iain
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-17-2006 03:06 AM
тАО01-17-2006 03:06 AM
Re: Proliant 1600 - Rebuild Issue
you must control that smart the Array is before controller and then must modernize the firmware of the cards. after to have created a volume raid from the panel f8 to the start you make to leave the smart start and then it would have to work.
reply for problem
reply for problem
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-24-2006 08:46 AM
тАО01-24-2006 08:46 AM
Re: Proliant 1600 - Rebuild Issue
What version of SmartStart are you using?
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP