- Community Home
- >
- Servers and Operating Systems
- >
- ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: Proliant MicroServer Gen8 installing new optic...
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-04-2014 11:33 PM
09-04-2014 11:33 PM
Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
Hi All,
Not sure if ths is the correct forum for Proliant MicroServers, here goes anyway..
Installed DVD Drive caddy to empty bay (server did not come with optical drive) in the server, when booting up the drive is not detected. Is there something I need to configure in the BIOS to enable the onboard SATA?
The server has HP Dynamic Smart Array B120i RAID Controller, the drives in the drive bays are all fine...
I have the Caddy connected to the board as pictured below....
HP ENVY 17-j005tx Notebook, HP ENVY Recline 27-k001a, HP ProLiant MicroServer Gen8 G2020T, HP MediaSmart EX495 Server, HP MediaVault 2020, HP ENVY 120 AiO Printer
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-05-2014 05:14 AM
09-05-2014 05:14 AM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
When you order the optional optical drive for the Microserver it has a split cable that attaches to the sata port where you're picture shows you're connected and the power is connected to the small plug on the top of the server. I don't see any reason why your configuration shouldn't work.
As the system goes through POST the optical drive should ID on a SATA controller as Port 5
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-05-2014 09:36 PM
09-05-2014 09:36 PM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
Hi Jimmy,
I replaced the Y-Cable I bought from ebay and removed the DVD Caddy.
I now connected the drive directly to the SATA port and using molex to 15 pin power to the drive. POST still doesn't detect the drive.
I suspect I may need to use the power from the power source specifically for the DVD drive, by doing so it may enable the SATA port on the motherboard...
2.JPG
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-05-2014 09:42 PM
09-05-2014 09:42 PM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
So now waiting for this to be delivered to try by using the power from the power for the DVD
http://www.ebay.com.au/itm/161213010038
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-06-2014 10:40 AM
09-06-2014 10:40 AM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
I just tried plugging a laptop hard disk multibay caddy into the connector that plugs onto the optical drive. This disk spins up, but the controller doesn't ID the drive during POST.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-06-2014 05:13 PM
09-06-2014 05:13 PM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
cool - so there must be a way to enable the on-board SATA OOD port - any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
09-06-2014 05:38 PM
09-06-2014 05:38 PM
Re: Proliant MicroServer Gen8 installing new optical drive (caddy) not detecting?
Jimmy, there is a blog here (http://www.adamfowlerit.com/2013/09/30/hp-proliant-microserver-gen8-real-world-usage/) says he connects the 5 SATA to SSD drive in one of the comments. Then a user comment also mentions the same.
So this port should smply come up if something is plugged into it.
I'm wondering if they both have the BIOS Set to AHCI mode, my BIOS is set to the B120i. If I changed it to AHCI mde will I lose my existing drive config? I'm not wanting to go through re-installing unless I really have to...
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP