- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- ProLiant Servers - Netservers
- >
- Re: SSH with LO100i version 1.21 on DL145 G2
ProLiant Servers - Netservers
1753774
Members
6851
Online
108799
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-13-2005 03:38 AM
тАО10-13-2005 03:38 AM
SSH with LO100i version 1.21 on DL145 G2
How do I setup ssh with the 1.21 version?
I tried to follow the instructions in the User Guide but I failed to make it work. I just get a
"Initiating Download..." and the I got disconnected.
It might be me but is 1.21 much slower than previous versions? Especially when you are trying to access the BIOS through the LO.
I tried to follow the instructions in the User Guide but I failed to make it work. I just get a
"Initiating Download..." and the I got disconnected.
It might be me but is 1.21 much slower than previous versions? Especially when you are trying to access the BIOS through the LO.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2006 12:24 AM
тАО01-18-2006 12:24 AM
Re: SSH with LO100i version 1.21 on DL145 G2
I've been having difficulty with this also. I can't even get as far as loading the SSH key, since it rejects the syntax shown in the manual:
/./map1/firmware/> load -source //172.17.21.1/sshkey -oemhpfileType key
Invalid parameters.
Did you at least get that bit to work?
/./map1/firmware/> load -source //172.17.21.1/sshkey -oemhpfileType key
Invalid parameters.
Did you at least get that bit to work?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2006 08:49 PM
тАО01-19-2006 08:49 PM
Re: SSH with LO100i version 1.21 on DL145 G2
I think I managed to install the key, but I can't remember how I did it. I haven't had the need of using the LO for a while...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP