- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- ILO not responding after reset network settings
Server Management - Remote Server Management
1753648
Members
5894
Online
108798
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2005 06:57 PM
10-11-2005 06:57 PM
ILO not responding after reset network settings
Hi all,
I have a server in a remote location and ILO (integrated ILO on Proliant DL380 G3) was not used. Now I want to use ILO, so I let the network port patched. Because I didn't knew any settings of ILO I used HPONCFG to reset the password, reset the whole ILO board, and set the IP settings to a fixed IP address. Then I rebooted ILO and rebooted the server as well. When I used HPONCFG to GET the IP address info, I see the settings are correct. But I still cannot ping the ILO board, or connect via HP Management in Windows. Is there something I forgot? Thanks in advance for your reaction.
Kind regards,
Cees
I have a server in a remote location and ILO (integrated ILO on Proliant DL380 G3) was not used. Now I want to use ILO, so I let the network port patched. Because I didn't knew any settings of ILO I used HPONCFG to reset the password, reset the whole ILO board, and set the IP settings to a fixed IP address. Then I rebooted ILO and rebooted the server as well. When I used HPONCFG to GET the IP address info, I see the settings are correct. But I still cannot ping the ILO board, or connect via HP Management in Windows. Is there something I forgot? Thanks in advance for your reaction.
Kind regards,
Cees
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-11-2005 07:00 PM
10-11-2005 07:00 PM
Re: ILO not responding after reset network settings
Just forgot, I also installed HP management pack 7.30 and the newest bios version on ILO.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP