- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: Access ILO2
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-07-2008 05:48 AM
тАО10-07-2008 05:48 AM
When boot server and press F8 ILO2 is asking a password? never use that, so unknown by me, Even the label with password will not work.
How to access or reset the ILO2 board?
Thanks in advance.
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-07-2008 07:14 AM
тАО10-07-2008 07:14 AM
Re: Access ILO2
Turn it off.
Lift the lid and look at the switch setting diagram on the underside.
Set the reset admin password switch on.
Turn it on.
Use any text as the password.
Change the password in admin properties
Turn it off.
Turn the switch off.
Put the lid back on.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-07-2008 08:52 PM
тАО10-07-2008 08:52 PM
SolutionIf your system has the PSP installed, you can change the admin password and the IP address using hponcfg and the proper xml files from the OS
NOTE: when hponcfg is run locally USER_LOGIN and PASSWORD are not used, but must have some value present for the xml to work
Change Admin Password
Change IP address
To disable iLO RBSU password
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-07-2008 11:19 PM
тАО10-07-2008 11:19 PM
Re: Access ILO2
Use hponcfg /reset which will reset the ILO then use hponcfg to dump the xml files.
ILO is ace.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-08-2008 10:55 AM
тАО10-08-2008 10:55 AM
Re: Access ILO2
Yes it works....
Only DNS on internet take a few minutes to find the right direction to my PC...Pffftt
Greetings from Holland..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-05-2008 03:06 AM
тАО12-05-2008 03:06 AM