- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Blade Ilo COnfiguration using hponcfg 1.1
Server Management - Remote Server Management
1752843
Members
3598
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2005 05:36 AM
тАО06-13-2005 05:36 AM
Blade Ilo COnfiguration using hponcfg 1.1
ilo Gurus,
Here ia an XML file that I am trying to upload to the iLO of a BL20p blade using hponcfg.exe v1.1
The settings go in fine except that that the DHCP_ENABLE remains Yes and hence the IP configuration is not applied. Anything that I am doing wrong? This is a Windows 2003 server.
This is the output when I get the values:
Here ia an XML file that I am trying to upload to the iLO of a BL20p blade using hponcfg.exe v1.1
The settings go in fine except that that the DHCP_ENABLE remains Yes and hence the IP configuration is not applied. Anything that I am doing wrong? This is a Windows 2003 server.
This is the output when I get the values:
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2005 07:29 PM
тАО06-13-2005 07:29 PM
Re: Blade Ilo COnfiguration using hponcfg 1.1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2005 04:00 AM
тАО06-14-2005 04:00 AM
Re: Blade Ilo COnfiguration using hponcfg 1.1
If you look at the XML file that was originally put in, the DHCP value was
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2005 04:53 AM
тАО09-30-2005 04:53 AM
Re: Blade Ilo COnfiguration using hponcfg 1.1
Did you every get this resolved. I'm having the same issue.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP