- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: How can I query the powersupplies via ssh to i...
Server Management - Remote Server Management
1748227
Members
4345
Online
108759
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2007 01:12 PM
тАО09-06-2007 01:12 PM
I can view lots of information with
'show /system1/fan1' etc but
'show /system1/powersupply1' gives an error
status=2
status_tag=COMMAND PROCESSING FAILED
error_tag=COMMAND ERROR-UNSPECIFIED
Invalid target.
powersupply1 is listed as a target if I run 'show /system1'
'show /system1/fan1' etc but
'show /system1/powersupply1' gives an error
status=2
status_tag=COMMAND PROCESSING FAILED
error_tag=COMMAND ERROR-UNSPECIFIED
Invalid target.
powersupply1 is listed as a target if I run 'show /system1'
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2007 02:04 PM
тАО09-06-2007 02:04 PM
Solution
What system are we talking about? When I try it on a DL380G5, I get:
status=0
status_tag=COMMAND COMPLETED
/system1/powersupply1
Targets
Properties
ElementName=Power Supply 1
OperationalStatus=Ok
HealthState=Ok
Verbs
cd version exit show set
status=0
status_tag=COMMAND COMPLETED
/system1/powersupply1
Targets
Properties
ElementName=Power Supply 1
OperationalStatus=Ok
HealthState=Ok
Verbs
cd version exit show set
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2007 02:29 PM
тАО09-06-2007 02:29 PM
Re: How can I query the powersupplies via ssh to ilo2?
My server is a DL380G5. It was running an older ilo firmware so I have updated that. Now the ssh is not working but once it comes up I will test it again.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-06-2007 06:47 PM
тАО09-06-2007 06:47 PM
Re: How can I query the powersupplies via ssh to ilo2?
After updating the ilo firmware, I had to restart ILO again. After that, the ssh worked and so does the 'show /system1/powersupply1' command.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP