- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Install of Firmware 1.13 to RILOE II
Server Management - Remote Server Management
1753865
Members
7689
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-29-2004 07:30 PM
тАО06-29-2004 07:30 PM
Install of Firmware 1.13 to RILOE II
I have two DL760 G2 serves in a 2-node Windows Server 2003/SQL Server 2000 cluster configuration. I have installed a RILOE II in each. Installation of the latest driver 3.2.1.0 and firmware 1.13 for the first RILOE II went fine. Installation of the latest driver 3.2.1.0 went fine, but the firmware 1.13 refuses to install nor the earlier version of the firmware 1.12. The present firmware version is 1.03. The RILOE is installed in PCI slot 9, with the 13/16 pin cable connected internally to the server, but without remote power per the installation guide.
Thank you.
jdh
Thank you.
jdh
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-30-2004 05:47 AM
тАО06-30-2004 05:47 AM
Re: Install of Firmware 1.13 to RILOE II
Try resetting RILOE II back to factory default, then reflash. (Remember to write down your settings before setting it back to factory default. New added users will be deleted). If this fails, try update with rompaq. Make sure RILOE is fully seated in slot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-07-2004 07:34 AM
тАО07-07-2004 07:34 AM
Re: Install of Firmware 1.13 to RILOE II
You can force the F/W upgrade as well by using SW3 on the RILOE-II. By default, all the switches should be "off" ... to force the F/W upgrade flip switch 3 to "on" and use the firmware upgrade disk method to upgrade the firmware. After it is complete, turn off the server and restore the switch to the "off" position and you should be off and running.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP