- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: RILOE ADD_USER error in CPQLOCFG
Server Management - Remote Server Management
1752281
Members
4749
Online
108786
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-18-2006 06:40 AM
тАО08-18-2006 06:40 AM
RILOE ADD_USER error in CPQLOCFG
I am attempting to add a new user with Administrative privilages to a RILOE with firmware 2.53A. I have an XML file which follows the standard in the sample files and doc. I am using CPLOCFG.EXE ver 2.25.
When I include the line
The script errors out at that point claiming a Syntax error at or near this line. If I remove this line, the script runs but the user ID does not have the Configure Riloe Access right when created.
If I use the older "SUPVERVISOR_PRIV value="Y" from the original RILOE User Guide, I get a message that this command is no longer supported and the User Right is not update.
How can I set that Configure Riloe Access right using the script to run through SIM without an error.
When I include the line
The script errors out at that point claiming a Syntax error at or near this line. If I remove this line, the script runs but the user ID does not have the Configure Riloe Access right when created.
If I use the older "SUPVERVISOR_PRIV value="Y" from the original RILOE User Guide, I get a message that this command is no longer supported and the User Right is not update.
How can I set that Configure Riloe Access right using the script to run through SIM without an error.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-18-2006 06:53 AM
тАО08-18-2006 06:53 AM
Re: RILOE ADD_USER error in CPQLOCFG
OK...shortly after posting this, I found another posting that showed an example where the syntax was "CONFIG_RILO_PRIV". That worked. I did not find that in any of the formal docs or sample files. They all documented it as CONFIG_ILO_PRIV".
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-18-2006 06:54 AM
тАО08-18-2006 06:54 AM
Re: RILOE ADD_USER error in CPQLOCFG
See last note.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP