Simpler Navigation for Servers and Operating Systems
Completed: a much simpler Servers and Operating Systems section of the Community. We combined many of the older boards, so you won't have to click through so many levels to get at the information you need. Check the consolidated boards here as many sub-forums are now single boards.
Server Management - Remote Server Management
cancel
Showing results for 
Search instead for 
Did you mean: 

iLO Web access not working

Gatis Visnevskis Gasha
Occasional Advisor

iLO Web access not working

Hi all,
got c7000 blade enclosure and one of the BL860c blades does not respond to iLO web (port 443).
Tried to reset it different ways.
ssh Admin/Admin@ip-address allows me to access management console. But 443/tcp port is not available whatever i change or reset.
"nmap" output from working ip address and non-working:
-=-=-=-
Not shown: 1710 closed ports
PORT STATE SERVICE
22/tcp open ssh
23/tcp open telnet
80/tcp open http
443/tcp open https
2023/tcp open xinuexpansion3
-=-=-=-
Not shown: 1711 closed ports
PORT STATE SERVICE
22/tcp open ssh
23/tcp open telnet
80/tcp open http
2023/tcp open xinuexpansion3
-=-=-=-
80 port always returns redirect code to https, no matter web access is enabled or not.

Any ideas?
This is fresh customers system, not mine, so no HP support is available at this moment.
9 REPLIES
rick jones
Honored Contributor

Re: iLO Web access not working

What do you see from an "SA" command while logged-in to the MP?
there is no rest for the wicked yet the virtuous have no pillows
Gatis Visnevskis Gasha
Occasional Advisor

Re: iLO Web access not working

Current Set Access Configuration:
T - Telnet : Enabled
W - Web SSL : Enabled
H - SSH : Enabled
I - IPMI over LAN : Disabled
C - Command Mode : MP Menu
-=-=-
telnet 10.aa.bb.14 443
Trying 10.aa.bb.14...
telnet: Unable to connect to remote host: Connection refused
kris rombauts
Honored Contributor

Re: iLO Web access not working

Hi Gatis,


- are you saying that another BL860C in the same C7000/C3000 blade enclosure does work correctly ?

- can you provide the L and H output of
the SO command in the MP CM menu ?

- what version of system f/w is on this blade ? Run SYSREV at the CM prompt to collect this info.


Kris
AndreBrown
Occasional Visitor

Re: iLO Web access not working

I've got a similar problem. I have two blades in the same enclosure. I can connect to one but not the other. They are two different models though. See my post here: http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1308734.

I've noticed a number of similar problems, none of which have posted resolutions.
Gatis Visnevskis Gasha
Occasional Advisor

Re: iLO Web access not working

Hi Kris,
firmware is pretty new, servers left HP factory in middle of november 2008.

see attached output.
(i tried also to re-generate certificates)
Gatis Visnevskis Gasha
Occasional Advisor

Re: iLO Web access not working

I just realized very bright idea (little bit funny however).
I can install system in one of the BL860c blades, then swap installed hard drives, and install again :)

I will write my success story here, if i will do it.
seamasters
HPE Pro

Re: iLO Web access not working

I was having the same trouble. The redirect was always failing. IE was saying that it could not connect to the server.

I finally found the SO (Security Options) command that let me generate a new certificate with better values than the default cert. Once I did that, I was able to connect into the ILO fine.
I am an HP employee.
Gatis Visnevskis Gasha
Occasional Advisor

Re: iLO Web access not working

Question is still open, but not so important for me right now. We sent system to final customer already :)
Two weeks ago i finally realized my idea - swapped HDD with another blade, installed fresh system, and then swapped back, assigned correct boot disk ID in firmware. (SSH console access is working).
Already tried that Certificate generation two or three times. No luck...
kris rombauts
Honored Contributor

Re: iLO Web access not working