- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Remote Server Management
- >
- Re: iLO2 on BL480
Server Management - Remote Server Management
1753259
Members
6234
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-16-2006 06:05 AM
тАО09-16-2006 06:05 AM
iLO2 on BL480
I am trying to configure my first blade enclosure. I have set up the enclosure and the gigabit ethernet switch. I can use the OA and I have access to the switch to make changes, all remotely using browser.
I have inserted the first of several BL480's into the enclosure. I am trying to get iLO2 to come up in a browser but have so far failed.
Before configuring the enclosure I created a DHCP server from an existing SLES10 box I set up to be my Suse installation server. I tested that I can get the addresses from the DHCP.
What I know of iLO2 is that it defaults to DHCP configuration. But when I try to access the iLO via the browser it just times out.
I can ping the address but cannot confirm that it was grabbed by iLO. I am remote so I cannot attach a cable to the front of the server and configure through the RBSU.
Any ideas?
I have inserted the first of several BL480's into the enclosure. I am trying to get iLO2 to come up in a browser but have so far failed.
Before configuring the enclosure I created a DHCP server from an existing SLES10 box I set up to be my Suse installation server. I tested that I can get the addresses from the DHCP.
What I know of iLO2 is that it defaults to DHCP configuration. But when I try to access the iLO via the browser it just times out.
I can ping the address but cannot confirm that it was grabbed by iLO. I am remote so I cannot attach a cable to the front of the server and configure through the RBSU.
Any ideas?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2006 01:49 PM
тАО09-17-2006 01:49 PM
Re: iLO2 on BL480
The c-class enclosure Onboard Administrator (OA) browser interface has a link to the iLO in the target blade. That would be the first place to consult to see if the iLO processor has network connectivity.
Also, the OA supports enclosure-based IP addressing. Check to see that this is not interfering with your DHCP settings. It could be that iLO is not using DHCP.
Also, the OA supports enclosure-based IP addressing. Check to see that this is not interfering with your DHCP settings. It could be that iLO is not using DHCP.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2006 07:58 PM
тАО09-17-2006 07:58 PM
Re: iLO2 on BL480
Hi,
Have you checked the Idle Timeout for ILO2 for the blade.
Try to flash the firmware for ILO2:
http://h18007.www1.hp.com/support/files/server/us/download/25225.html
Regards
Have you checked the Idle Timeout for ILO2 for the blade.
Try to flash the firmware for ILO2:
http://h18007.www1.hp.com/support/files/server/us/download/25225.html
Regards
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2006 12:25 AM
тАО09-18-2006 12:25 AM
Re: iLO2 on BL480
Looks like it was something between the ILO port and the DHCP server. I changed the range of IP's available on my DHCP and then rebooted both the DHCP and the server. After that I was able to view the browser page. Thanks to those that responded.
Cheers,
henri
Cheers,
henri
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP