- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- Re: Blade Power Enclosure in SIM 5.0 and other Ide...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-11-2005 06:53 AM
тАО10-11-2005 06:53 AM
Blade Power Enclosure in SIM 5.0 and other Identification Issues
Have several Blade power supply enclosures that are showing up in SIM, but they show each of the power slots as being empty. The Chassis enclosures have been updated to the latest firmware, and the ilo's are all running ver 1.82, and I have run discovery on all the Servers and their ilo processors.
Anyone else run into this?
ALso, I have a few entries that just will not seem to associate themselves with each other, for example, an ilo will not associate with its server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2005 05:28 AM
тАО11-01-2005 05:28 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
The HP tech on the phone advised me to basically power down everything and restart, which I did, and to no avail.
Anyone else experience this issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-01-2005 08:26 PM
тАО11-01-2005 08:26 PM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
Though for some reason, one out of 10 Power Enclosures shows up in HPSIM with the correct amount of power modules in the bays (see attachment). The general status of the Power Enclosure is still "Unknown", just like the other nine Power Enclosures that are shown in HPSIM.
All of the BL20p-enclosures on all five racks show up correctly, with all available information, both in HPSIM and on the local ILO-boards.
All 10 Power Enclosures do show up correctly in the Rack View on the ILO-boards.
Now what's the difference? Until now, the only thing I see is that the single Enclosure that shows the power modules has:
-Power Redundancy Load Share Cable Not Present
-Load Balance Wire Not Present
On all the other nine Power Enclosures, the "Load Balance Wire" IS present and I do not get the "Power Reduncancy" line in the enclosure status.
Maybe the MIB that is used to detect the Power Enclosure status is not correct, or the "HP Proliant Rack Infrastructure Interface Service" needs an update (running Support Pack 7.40 now).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-15-2005 08:14 PM
тАО11-15-2005 08:14 PM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
Also, when I try to do a data collection on, for example, one of the enclosures, I get "Data collection was skipped for this system because the system is suspended or inaccessible."
Still no ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-16-2005 12:36 AM
тАО11-16-2005 12:36 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-16-2005 12:38 AM
тАО11-16-2005 12:38 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-16-2005 03:09 AM
тАО11-16-2005 03:09 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
:)
Thanks for your comments all. Looking forward to the fix.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-17-2005 01:22 AM
тАО11-17-2005 01:22 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-07-2005 05:51 AM
тАО12-07-2005 05:51 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
Has anyone heard from HP whether there's a fix for this issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-28-2005 03:26 AM
тАО12-28-2005 03:26 AM
Re: Blade Power Enclosure in SIM 5.0 and other Identification Issues
I have read that becuase the power enclosures don't have NIC's, they will always show a question mark, but I atleast want SIM to recognize what power supplies are where and what blades are where.