- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- Re: Configure SIM icmp status pulling
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 02:33 AM
тАО11-20-2008 02:33 AM
Configure SIM icmp status pulling
i configure SIM server and everything works fine except that when a machine is restarting the SIM doesn't let me know about it unless it is down at least 5 minutes. i tried my best to find where i can tune this option but with no success. i want the SIM to know if machine is not responding to ping for more then 30 seconds.
please advise
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 03:43 AM
тАО11-20-2008 03:43 AM
Re: Configure SIM icmp status pulling
if you go into tasks --> view all and edit the hardware polling task you should be able to see the current settings and adjust accordingly.
hope this helps
good luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 04:09 AM
тАО11-20-2008 04:09 AM
Re: Configure SIM icmp status pulling
i check this area and there is nothing about ICMP or ping and anyway the timeout is already 4 seconds by default and as i said SIM realize that some machine is down only after 5 minutes!
10x in advanced.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 04:40 AM
тАО11-20-2008 04:40 AM
Re: Configure SIM icmp status pulling
how often is the task scheduled to run ?
in options --> protocol --> global is icmp marked for reachability ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2008 11:31 AM
тАО11-20-2008 11:31 AM
Re: Configure SIM icmp status pulling
A server can reboot much quicker than 5 minutes.
You can change the frequency of the polling task.
But, and I'm not sure why this changed, ICMP is not listed as one of the protocols used. In an earlier version of HPSIM I set up an ICMP Ping only polling task that ran every minute.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-21-2008 12:11 PM
тАО11-21-2008 12:11 PM
Re: Configure SIM icmp status pulling
to bad that there is no ICMP task!