- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- Re: Not getting notifications when hardware fails.
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 08:06 AM
тАО08-31-2006 08:06 AM
Re: Not getting notifications when hardware fails.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 08:20 AM
тАО08-31-2006 08:20 AM
Re: Not getting notifications when hardware fails.
For hardware problems the agents on the remote server detects the error and generates an SNMP Trap. This trap gets sent to HPSIM and then HPSIM generates the relevent event.
If from a server you use the Send SNMP Trap from the HP Management Agents GUI and you get no event on HPSIM then you do not have SNMP Set correctly.
You need community names set up, they're case sensitive, in HPSIM and on the remote server. There should be a read only and a read/write (or read/create).
In addition on the remote server the HPSIM Servers address nees to be in the Traps section of the SNMP Properties, again using a community name that HPSIM has configured.
The remote server needs to know what community name to use and where to send the SNMP Trap.
Also on the HPSIM Server, in the SNMP properties I set SNMP to Allow All Hosts.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 08:22 AM
тАО08-31-2006 08:22 AM
Re: Not getting notifications when hardware fails.
snmputil trap
...which listens for SNMP traps. I then sent a test trap from my managed server using the HP Agent control panel and the test trap popped up in snmputil.
So at least I know my traps are getting to SIM.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 08:40 AM
тАО08-31-2006 08:40 AM
Re: Not getting notifications when hardware fails.
Is there anywhere else other than in the Options > Protocol Settings > Global Protocol Settings that I need to enable SNMP?
It really seems like for some reason my SIM installation is just not listening to traps for some reason.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 08:51 AM
тАО08-31-2006 08:51 AM
Re: Not getting notifications when hardware fails.
I see from searching in this forum that a few other people have had issues where occasionally SIM craps out and needs a service restart.
Thanks to everyone for their helpful posts...
-Simon.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2006 07:26 PM
тАО08-31-2006 07:26 PM
Re: Not getting notifications when hardware fails.
I would suggest you to enable all services on SNMP AGENT tab and restart SIM services and see if that helps.
Albert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-18-2006 12:55 AM
тАО09-18-2006 12:55 AM
Re: Not getting notifications when hardware fails.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-19-2006 09:40 AM
тАО09-19-2006 09:40 AM
Re: Not getting notifications when hardware fails.
Have you tried using the SNMPUtil as suggested above?
Does that record any traps?
If not, then it indicates the problem is at the server sending the traps.
Anything in between that would stop traps? e.g. firewalls
Check that on server the HPSIM Server is added to the Traps tab of SNMP. Use an IP Address rather than a name.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2006 05:13 AM
тАО09-20-2006 05:13 AM
Re: Not getting notifications when hardware fails.
I think Rob pointed out a good point. To check if anything is eating up those traps.
Check this link sounds very similar to your problem.
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1059798
Albert
- « Previous
-
- 1
- 2
- Next »