- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- WBEM and SSH Errors
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-02-2012 12:46 PM
07-02-2012 12:46 PM
WBEM and SSH Errors
I have insight manager installed but trying to discover the only host and getting errors below. ANy ideas? Does WBEM need to be install on target machine? Can this be done manually as trying through CMS does not work for WBEM & SSH.
WBEM protocol settings are not valid/enabled for this system in HP SIM. Check yo
ur HP SIM settings for identification via WBEM.
Subscribe to WBEM / WMI Indications ................................. [FAILED
Configure SSH for host-based authentication ......................... [FAILED]
Configuration failed to complete due to the following exception:
Connection
to the target system failed due to Connection refused: connect.Target system mig
ht be down or does not have a SSH server. The network connection problem could a
lso cause this issue.
- Tags:
- ssh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-03-2012 05:57 AM
07-03-2012 05:57 AM
Re: WBEM and SSH Errors
Hi,
The WBEM agents need to be installed on the target system - what type of system is it?
WBEM was introduced to replace SNMP due to the lack of security on SNMP V1 and V2 -
this security issue was fixed in SNMP V3 which is both encrypted and authenticated.
If you want to use the WBEM protocol - you will need to specify the target credentials to
use on the CMS.
Hope this helps - regards,
Steve.B.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-03-2012 09:34 AM
07-03-2012 09:34 AM
Re: WBEM and SSH Errors
in installed WBEM but keep getting this error
WBEM protocol settings are not valid/enabled for this system in HP SIM. Check yo
ur HP SIM settings for identification via WBEM.
Subscribe to WBEM / WMI Indications ................................. [FAILED]
Send test WBEM/ WMI indication from the system ...................... [FAILED]
CMS has to be subscribed for WBEM / WMI indications before it can receive a test
indication.