- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Server Management - Systems Insight Manager
- >
- Re: default task "hardware status polling for serv...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2009 05:10 PM
тАО08-31-2009 05:10 PM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2009 11:57 PM
тАО08-31-2009 11:57 PM
Re: default task "hardware status polling for server" didn't send alert
If there's a hardware poblem on the server (e.g. failed disk) then the agents pick that up and send an SNMP Trap back to the HP SIM Server.
For that to succeed you need the Trap Destination set on the servers.
You can test the set up, from Control Panel run up the HP Management Agents GUI and use the SNMP Trap Send button which should generate a Major Event for the server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2009 01:29 AM
тАО09-01-2009 01:29 AM
Re: default task "hardware status polling for server" didn't send alert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2009 12:50 PM
тАО09-01-2009 12:50 PM
SolutionThey are two separate processes.
If a server crashes or there's a network issue then the agents cannot send anything to HPSIM. That's where the polling task fits in.
It also updates the HW Icon if the HW Agents have reported an issue.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2009 05:14 PM
тАО09-01-2009 05:14 PM
Re: default task "hardware status polling for server" didn't send alert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2009 06:58 PM
тАО09-01-2009 06:58 PM
Re: default task "hardware status polling for server" didn't send alert
Alerts are triggered when they happen, but they're also get triggered if the agents get a restart.
So if the disk has already failed you will not get a message from the agents.
It's the same with the threshold settings, it's a one off snmp trap when the threshold is breached. After that you will get them if the agents restart.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2009 04:43 AM
тАО09-02-2009 04:43 AM