- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Servers - General
- >
- HP Mgmt Card for XR UPS problems
Servers - General
1753902
Members
9736
Online
108810
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-04-2010 04:13 AM
08-04-2010 04:13 AM
HP Mgmt Card for XR UPS problems
After a bit of advice please.
I have purchased a HP Mgmt card for a RX5500XR. I have popped the card into the UPS and followed the instructions of how to setup the configuration. However the intructions state that I should see a prompt "Press any key in 5 seconds". I don't see this all I get is a load of ascii characters appearing.
At first I thought my COM baud rate was wrong etc, but I've doubled checked the settings of 115200/8/None/1/None is the same as in my terminal emulation program and it is the same. I have pressed the reset button a few times, but still just get rubbish returned to the emulation program.
I didnt think I would have to do this as I was hoping the card got an IP address from my DHCP server, but it doesnt.
Any ideas? Im guessing it is not in Serial Mode or something. Please help.
I have purchased a HP Mgmt card for a RX5500XR. I have popped the card into the UPS and followed the instructions of how to setup the configuration. However the intructions state that I should see a prompt "Press any key in 5 seconds". I don't see this all I get is a load of ascii characters appearing.
At first I thought my COM baud rate was wrong etc, but I've doubled checked the settings of 115200/8/None/1/None is the same as in my terminal emulation program and it is the same. I have pressed the reset button a few times, but still just get rubbish returned to the emulation program.
I didnt think I would have to do this as I was hoping the card got an IP address from my DHCP server, but it doesnt.
Any ideas? Im guessing it is not in Serial Mode or something. Please help.
- Tags:
- UPS
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-11-2010 07:49 AM
08-11-2010 07:49 AM
Re: HP Mgmt Card for XR UPS problems
Few things to check:
-Use HP provided green serial-to-RJ45 adapter?
-Connect to the correct Configuration port? (lower-left corner RJ45 jack)
-Reseat the HP Management Module (it can be hotplugged)
-Try on different server
-Hyperterminal setting is Emulation= "Auto Detect" and Terminal= "ANSI"
-It could be a bad card?
You would see the same screen as in the attachment.
Brian
-Use HP provided green serial-to-RJ45 adapter?
-Connect to the correct Configuration port? (lower-left corner RJ45 jack)
-Reseat the HP Management Module (it can be hotplugged)
-Try on different server
-Hyperterminal setting is Emulation= "Auto Detect" and Terminal= "ANSI"
-It could be a bad card?
You would see the same screen as in the attachment.
Brian
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP