- Community Home
- >
- Servers and Operating Systems
- >
- Servers - General
- >
- HP UPS Management Module UPS-Pass Through Mode
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-10-2010 09:43 AM
02-10-2010 09:43 AM
Basically When I reset the card and push a button to inturupt the boot process, I am presented with 3 options, 1 configure card, 2 UPS-Pass Through, 3 Exit. When I push 2 the screen just sits there and says entering pass-through mode. Is there a trick to making this work? Thanks.
Solved! Go to Solution.
- Tags:
- UPS
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-11-2010 08:39 AM
02-11-2010 08:39 AM
SolutionI guess you see the Overview Meter wrongly report as a 3-phase UPS?
First, upgrade the FW of UPS R3000XR (make sure not a R/T3000) to FW= 2.02(once select option 2, the Config Port on the card will act as a serial port of the UPS, the UPS FW flash utility would communicate directly to UPS) or you can use the built-in serial port on UPS to flash the UPS (9600,8,n,1,none)
If your card has an old FW=1.20 then the lastest HPMM FW= 2.1.3, you can flash via the Config Port (as is, not set to Pass-Through) or via Network port.
Caution; both flash utilities are not the same!
Find them here:
http://h18004.www1.hp.com/products/servers/platforms/rackandpower.html
Brian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-11-2010 08:47 AM
02-11-2010 08:47 AM
Re: HP UPS Management Module UPS-Pass Through Mode
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-11-2010 01:02 PM
02-11-2010 01:02 PM
Re: HP UPS Management Module UPS-Pass Through Mode
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
02-12-2010 06:32 AM
02-12-2010 06:32 AM
Re: HP UPS Management Module UPS-Pass Through Mode
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP