- Community Home
- >
- Servers and Operating Systems
- >
- HPE ProLiant
- >
- Servers - General
- >
- Re: Ml10 Gen9 E3-1225v5 not all lanes useable for ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-11-2021 03:25 AM
тАО05-11-2021 03:25 AM
Ml10 Gen9 E3-1225v5 not all lanes useable for upgrade to three i.e. x4 + x4 + x8 pci cards?
Hello all,
i want to upgrade from a working setup using
1. m.2 on pci card x4 lanes
2. m.2 on pci card x4 lanes
3. 10GBe mellanox connectx-3 C11A x4 lanes
upgradiung to
3. 40Gbe mellanox connectx-3 C353A x8 lanes
I can't find a solution where both m.2 drives and C353A are all working. Sometimes it doesn't boot at all . If it boots with all three cards installed everytime one drive does not show up. Did i miss something in manual:
https://support.hpe.com/hpesc/public/docDisplay?docId=c04960468 on page 10
where i found 2x8 + 1x4 + 1x1 bus width. That should be enough for my upgrade?
I am grateful for any advice what i am missing?
Ralf
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-11-2021 08:01 PM
тАО05-11-2021 08:01 PM
Re: Ml10 Gen9 E3-1225v5 not all lanes useable for upgrade to three i.e. x4 + x4 + x8 pci cards?
Hello,
I think the configuration looks good but just wanted to check if these cards are HPE branded and supported on the server?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-11-2021 08:51 PM
тАО05-11-2021 08:51 PM
Re: Ml10 Gen9 E3-1225v5 not all lanes useable for upgrade to three i.e. x4 + x4 + x8 pci cards?
Hi Anu_K
thanks for your answer but i can not imagine that the missing HPE brand causes the problem because any combination of 2 of this cards out of the 3 i want to use is working well.
Ralf