Skip to ContentSkip to Footer
Start of content
- Community Home
- >
- Servers and Operating Systems
- >
- Servers - General
- >
- R12000 UPS
Servers - General
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
10-22-2010 10:01 AM
10-22-2010 10:01 AM
R12000 UPS
I have an R12000 ups connected to a proliant dl380g6. Firmware on the ups is 2.0.2. The firmware on the management module is 2.1.3. The remote agent installed is version 4.5. On the download site it shows that version 5.0 is available but when it's installed you get version 4.5.
I can configure and connect to the management module with no problem with hyperterminal, telnet or through the web interfacce. The problem is that the remote agent shows there is no device even though, if I go to connect, I can see the IP address of the UPSMM and connect to it. The remote agent will show that it's connected for approximately 10 seconds then show there is no device for approximately 7 minutes. In other words, the agent will not stay connected. Any help would be appreciated.
I can configure and connect to the management module with no problem with hyperterminal, telnet or through the web interfacce. The problem is that the remote agent shows there is no device even though, if I go to connect, I can see the IP address of the UPSMM and connect to it. The remote agent will show that it's connected for approximately 10 seconds then show there is no device for approximately 7 minutes. In other words, the agent will not stay connected. Any help would be appreciated.
- Tags:
- UPS
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
10-25-2010 05:58 AM
10-25-2010 05:58 AM
Re: R12000 UPS
Just to make sure when configure the PPA, select the second field (Management Module #2) for "No Server", don't leave it as "Any Server". Second field is used for redundancy.
Brian
Brian
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
End of content
United States
Hewlett Packard Enterprise International
Communities
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP