- Community Home
- >
- Servers and Operating Systems
- >
- Servers - General
- >
- UPS Management Module Mac address
-
- Forums
-
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
- HPE Blog, Austria, Germany & Switzerland
- Blog HPE, France
- HPE Blog, Italy
- HPE Blog, Japan
- HPE Blog, Middle East
- HPE Blog, Russia
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
-
Blogs
- Advancing Life & Work
- Advantage EX
- Alliances
- Around the Storage Block
- HPE Blog, Latin America
- HPE Blog, Middle East
- HPE Blog, Saudi Arabia
- HPE Blog, South Africa
- HPE Blog, UK & Ireland
- HPE Ezmeral: Uncut
- OEM Solutions
- Servers & Systems: The Right Compute
- Tech Insights
- The Cloud Experience Everywhere
-
Information
- Community
- Welcome
- Getting Started
- FAQ
- Ranking Overview
- Rules of Participation
- Tips and Tricks
- Resources
- Announcements
- Email us
- Feedback
- Information Libraries
- Integrated Systems
- Networking
- Servers
- Storage
- Other HPE Sites
- Support Center
- Aruba Airheads Community
- Enterprise.nxt
- HPE Dev Community
- Cloud28+ Community
- Marketplace
-
Forums
-
Blogs
-
Information
-
English
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-14-2009 09:07 AM
07-14-2009 09:07 AM
UPS Management Module Mac address
I tried to restore the setttings to factory defaults and it goes back to the same think.
Has anyone tried this:
1. In the HP UPS Management Module Service Menu, go to the Module
Configuration menu, and then select the r option to enter the Restore
Configuration to Manufacturer Settings submenu.
2. Select BootP or set a static IP address.
3. Enter the following, case-sensitive commands at the command prompt:
a. GOMAC—Restores the MAC address of the
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
07-15-2009 06:26 AM
07-15-2009 06:26 AM
Re: UPS Management Module Mac address
-Those hidden commands should enter at the Module Configuration Menu. MAC address is entered with a space in between bytes.
-It seems your new module's FW could have been corrupted. Try to flash it with FW v2.0 again, download it from here:
"http://h18004.www1.hp.com/products/servers/proliantstorage/power-protection/software/module/ups/index.html"
Brian
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-14-2009 10:52 PM
12-14-2009 10:52 PM
Re: UPS Management Module Mac address
How did you change serial number and Hardware version?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-14-2009 10:56 PM
12-14-2009 10:56 PM
Re: UPS Management Module Mac address
I also have to change Hardwareversion (currently reading 0) and serial number
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Email to a Friend
- Report Inappropriate Content
12-15-2009 11:41 AM
12-15-2009 11:41 AM
Re: UPS Management Module Mac address
http://www.staff.stir.ac.uk/p.g.ward/af401afirmware.html
The command for the Serial number is GONU
Hewlett Packard Enterprise International
- Communities
- HPE Blogs and Forum
© Copyright 2021 Hewlett Packard Enterprise Development LP