- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: how to start the node while cluster and packag...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-08-2013 01:17 PM - last edited on 12-08-2013 11:43 PM by Maiko-I
12-08-2013 01:17 PM - last edited on 12-08-2013 11:43 PM by Maiko-I
how to start the node while cluster and package service running
in our setup command cmviewcl output
CLUSTER STATUS
clu01 up
NODE STATUS STATE
e01 up running
PACKAGE STATUS STATE AUTO_RUN NODE
d1 up running enabled e01
NODE STATUS STATE
e02 down halted
i want to join e02 in cluster node, please share the command with out affecting the running application how to join the node
P.S. This thread has been moved from HP-UX > LVM and VxVM to HP-UX > Serviceguard. - Hp Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-08-2013 04:06 PM
12-08-2013 04:06 PM
Re: how to start the node while cluster and package service running
The command you want is 'cmrunnode'
You should run:
# cmrunnode e02
You can find a version of the man page here:
http://www.unix.com/man-page/all/1m/cmrunnode/
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-08-2013 04:08 PM
12-08-2013 04:08 PM
Re: how to start the node while cluster and package service running
thanks for your reply
i want to know if i give cmrunnode e02 , it is affecting running application e02. pls confirm
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-09-2013 07:03 AM
12-09-2013 07:03 AM
Re: how to start the node while cluster and package service running
>>i want to know if i give cmrunnode e02 , it is affecting running application e02. pls confirm
There should be nothing from service guard that is affected by running that command.
If there is anything else running on that server, it might be affected, but I can't say for sure.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-26-2014 07:13 AM
01-26-2014 07:13 AM
Re: how to start the node while cluster and package service running
Hi,
"cmrunnode" will not effect to the running package unless you configure that node "e02" as primary node and enabled package automatic fail back
please share cmviewcl -v and following files if you can
/etc/cmcluster/d1/d1.cntl
/etc/cmcluster/d1/d1.conf
i.e. location may be difference in your system
regards,
Primesh