MSA Storage
1748104 Members
4619 Online
108758 Solutions
New Discussion

Re: MSA2040 Firmware update error Message

 
SOLVED
Go to solution
Michael Ziegler
Occasional Advisor

MSA2040 Firmware update error Message

When trying to update my firmware from GL101R001 to GL210R004 it says "an newer version of the firmware allready install, want to downgrade?

 

I think this is an fault message, the firmware GL101R001 ist from September 2013, the GL210 ist from July 2015.

 

Any help here?

 

Is it ok to upgrade without firmware steps between?

 

Best regards

11 REPLIES 11
AnkitM
Trusted Contributor

Re: MSA2040 Firmware update error Message

Please, follow below Upgrade Path and check if it works:

GL105P003 - http://h20564.www2.hp.com/hpsc/swd/public/detail?swItemId=MTX_8f6a766557ec49a9adfe0e190f#tab3
GL210R004 - http://h20564.www2.hp.com/hpsc/swd/public/detail?sp4ts.oid=5386654&swItemId=MTX_4e54b0ca76104f10942471e970&swEnvOid=4064#tab1

 

Are you located in United States?

Was your question answered correctly? If so, please remember to mark your question Answered when you get the correct answer and award KUDOS! to the person providing the answer. This helps others searching for a similar issue.
Michael Ziegler
Occasional Advisor

Re: MSA2040 Firmware update error Message

The Update from GL101R001 to GL105P003 was done. Everything fine with this version.

 

The Update to the final firmware GL210R004 failed.

Here is a part of the logfile (cpqsetup):

--------------------------------------------------------------------------- Setup Session Beginned on 21.07.2015 - 21:05:01 --------------------------------------------------------------------------- Command Line Parameters Given: Controller IP is :192.168.179.25 Beginning Interactive Session... Name: Online ROM Flash Component for Windows - HP MSA 1040/2040 Storage Arrays New Version: GL105P003 The software is installed but is not up to date. Current Version: GL101R001 Device flash Successful - MSA 2040 SAS : Controller A Detailed log in :MSA2000_192_168_179_25.log The operation was successful. --------------------------------------------------------------------------- Session Ended on 21.07.2015 - 21:29:12 ---------------------------------------------------------------------------

 

 

--------------------------------------------------------------------------- Setup Session Beginned on 21.07.2015 - 21:31:30 --------------------------------------------------------------------------- Command Line Parameters Given: Controller IP is :192.168.179.25 Beginning Interactive Session... Name: Online ROM Flash Component for Windows - HP MSA 1040/2040 Storage Arrays New Version: GL210R004 The software is installed, but the installed version is newer than the version you are attempting to install. Current Version: GL105P003 Device flash Unsuccessful - MSA 2040 SAS : Controller B Detailed log in :MSA2000_192_168_179_25.log The operation was not successful. --------------------------------------------------------------------------- Session Ended on 21.07.2015 - 21:36:53 ---------------------------------------------------------------------------

 

 

The more detailed logfile with both installation processes is attached.

 

 

Should i try another firmware step between?

 

Version:GL200P002 (5 Mar 2015)

Version:GL200R007 (1 Dec 2014)

AnkitM
Trusted Contributor

Re: MSA2040 Firmware update error Message

Yes, Start with Version:GL200P002 (5 Mar 2015)

 

If you are in United States, I don't mind calling you.

Was your question answered correctly? If so, please remember to mark your question Answered when you get the correct answer and award KUDOS! to the person providing the answer. This helps others searching for a similar issue.
Michael Ziegler
Occasional Advisor

Re: MSA2040 Firmware update error Message

Thanks, i will give it a try today night.

 

By having only one controller at this MSA2040, its not possible to try the update process during working hours.

 

Me being from Germany, a call is not necessary.

AnkitM
Trusted Contributor

Re: MSA2040 Firmware update error Message

Okay, No worries.

Was your question answered correctly? If so, please remember to mark your question Answered when you get the correct answer and award KUDOS! to the person providing the answer. This helps others searching for a similar issue.
Michael Ziegler
Occasional Advisor

Update MSA2040 Firmware update error Message

Managed to update to GL200P002

Messages show below.

 

Storage Controller firmware was installed successfully. (new version: GLS200R12-01)

The Management Controller booted up. MC firmware version: GLM200R017-01

 

Everything booted up fine, v2 ist fully functional.

 

But when trying to update to GL210R004, still the same error shows up:

 

The Intaller says: "A newer Version of this firmware already installed...)

 

Im on a dead end here, perhaps i should contact HP support.

Torsten.
Acclaimed Contributor

Re: MSA2040 Firmware update error Message

My understanding of this advisory

 

http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c04714455&sp4ts.oid=243739

 

is - try the update again.

 

According to the release notes to steps are neccessary.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
Michael Ziegler
Occasional Advisor

Re: Update MSA2040 Firmware update error Message

In Addition to my last post, here you can see the logfile entrys:

 

--------------------------------------------------------------------------- Setup Session Beginned on 22.07.2015 - 23:09:46 --------------------------------------------------------------------------- Command Line Parameters Given: Controller IP is :192.168.179.25 Beginning Interactive Session... Name: Online ROM Flash Component for Windows - HP MSA 1040/2040 Storage Arrays New Version: GL200P002 The software is installed but is not up to date. Current Version: GL105P003 Device flash Successful - MSA 2040 SAS : Controller A Detailed log in :MSA2000_192_168_179_25.log The operation was successful. --------------------------------------------------------------------------- Session Ended on 22.07.2015 - 23:31:51 ---------------------------------------------------------------------------

 

@ Thorsten: this update from GL105P003 to GL200P002 went all fine,

the advisory in http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c04714455&sp4ts.oid=243739 is about different versions of component firmware versions, but in this machine, all firmwares match.

 

The real problem shows below. The Updater thinks that GL200P002 ist newer than GL210R004 and does not start the update process. Strange behavior. Perhaps a wrong date stamp in the GL210R004 firmware updater?

 

 

--------------------------------------------------------------------------- Setup Session Beginned on 22.07.2015 - 23:32:35 --------------------------------------------------------------------------- Command Line Parameters Given: Controller IP is :192.168.179.25 Beginning Interactive Session... Name: Online ROM Flash Component for Windows - HP MSA 1040/2040 Storage Arrays New Version: GL210R004 The software is installed, but the installed version is newer than the version you are attempting to install. Current Version: GL200P002 --------------------------------------------------------------------------- Session Ended on 22.07.2015 - 23:33:21 ---------------------------------------------------------------------------

Torsten.
Acclaimed Contributor
Solution

Re: Update MSA2040 Firmware update error Message

I have never seen such issue before, but I never use the windows installer tool.

 

Consider to unpack the bundle and use the *.bin file with ftp (see release notes for instructions).

 

Disable PFU and update the controllers ony by one.

 

This always worked for me.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!