- Community Home
- >
- Storage
- >
- Entry Storage Systems
- >
- StoreEasy Storage
- >
- Re: HP 3-in-1 Firmware Instal
StoreEasy Storage
1753584
Members
6433
Online
108796
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-21-2009 05:34 PM
04-21-2009 05:34 PM
HP 3-in-1 Firmware Instal
I have hard reset this device and am attempting to reload the firmware. It is pingable at the address but can be seen only by Norton 360. One cannot browse to it by IP address or machine name, it is not visible on the network.
I have the firmware ("hpnas_split.nas") and "nasload.exe" and "nasunpack.exe" all loaded in the same directory from where I run the nasload instruction with the following sequence "nasload /a /s /U /P /f hpnas_split.nas". I have run it with both the /s switch and without it. I get the following:
Remote machine BRCM_TEMP_NAS ,at address 172.16.66.217> has requested a firmware download.
Downloading hpnas_split.nas...
ERROR: Transfer failed: 10053
I would be grateful for any suggestions.
I have the firmware ("hpnas_split.nas") and "nasload.exe" and "nasunpack.exe" all loaded in the same directory from where I run the nasload instruction with the following sequence "nasload /a /s /U /P /f hpnas_split.nas". I have run it with both the /s switch and without it. I get the following:
Remote machine BRCM_TEMP_NAS ,at address 172.16.66.217> has requested a firmware download.
Downloading hpnas_split.nas...
ERROR: Transfer failed: 10053
I would be grateful for any suggestions.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-23-2009 03:19 AM
04-23-2009 03:19 AM
Re: HP 3-in-1 Firmware Instal
hi
should be better to enter this question
on desktop/notebooks forum
JYP
should be better to enter this question
on desktop/notebooks forum
JYP
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP