StoreEasy Storage

HP StoreEasy 1450 fail to startup, Please Help

 
SOLVED
Go to solution
faman
Visitor

HP StoreEasy 1450 fail to startup, Please Help

Hi All

My StoreEasy 1450 is failled after mains failure. The LED indicators ( 4 LED ) are quickly blinks and repeats. Could anyone help with this issue. Many Thanks

6 REPLIES 6
ram_eranki
HPE Pro

Re: HP StoreEasy 1450 fail to startup, Please Help

Refer this : https://support.hpe.com/hpesc/public/docDisplay?docLocale=en_US&docId=c04444491

for information on LED indicators and status.

I am a HPE Employee

Accept or Kudo

ArunKKR
HPE Pro
Solution

Re: HP StoreEasy 1450 fail to startup, Please Help

Hi,

 

The server has an ilo management NIC port which might still be working even if server does not power on. If ilo  was configured earlier and is accessible , log in to ilo menu and check the hardware status and the events in integrated management log.

 

The Storeasy 1450 server is based on DL160 Gen9 proliant server.

Please check the front power fault LED status as mentioned in page 92 of the server maintenance guide at the below link:

 

https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-c04430745

 

The LED status should give a clue as to which hardware could be faulty.

 

The storeEasy 1450 server is shipped usually only with single power supply unit. 

If you have a different server with identical PSU and same part number you may try installing that.

 

 

 

 

 

 

 

 

While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company

Accept or Kudo

faman
Visitor

Re: HP StoreEasy 1450 fail to startup, Please Help

IMG-20211230-WA0016.jpg

Could anyone please help advise the above warning message for a HP storeasy 1450? Many thanks in advance. 

ArunKKR
HPE Pro

Re: HP StoreEasy 1450 fail to startup, Please Help

Hi,

1) Remove the AC power cord for 10-15 seconds and then reconnect it.

2) Power on the system if the Health LED shows solid green.

If issue persists try minimal hardware configuration by removing any add on PCI cards.

 

Clear nvram using the steps listed in the below web link:

https://support.hpe.com/hpesc/public/docDisplay?docId=mmr_kc-0128631

 

If issue persists you might need to log a support case with HPE to get the AHS logs reviewed and replace any faulty hardware.

 

 

 

 

While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company

Accept or Kudo

faman
Visitor

Re: HP StoreEasy 1450 fail to startup, Please Help

Hi 

I have tried a new power supply unit in my StoreEasy 1450, the situation(symptoms) is changed. please refer the following link for reference ( https://youtu.be/CJkxZ7GsB78 ). Many Thanks in advance. 

 

ArunKKR
HPE Pro

Re: HP StoreEasy 1450 fail to startup, Please Help

Hi ,

As per LED indication (8 flashes)  power backplane or storage backplane would be the cause.

Reference Page 92 of server maintenance guide:

https://support.hpe.com/hpesc/public/docDisplay?docId=c04430745&docLocale=en_US

I would suggest to get a case logged with HPE support for log analysis.

While I am an HPE Employee, all of my comments (whether noted or not), are my own and are not any official representation of the company

Accept or Kudo