- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Connect DLT 8000 to 9000/800/K380
StoreEver Tape Storage
1753637
Members
5489
Online
108798
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-27-2004 08:42 PM
тАО05-27-2004 08:42 PM
Connect DLT 8000 to 9000/800/K380
Hi,
Are any patches needed for a default install of HP-UX 11.00 in order to connect a DLT 8000 FW SCSI to a 9000/800/K380 system to "optional" connector in core I/O board, HW path 10/8?
What driver should be the suitable one? stape? tape2?
Should this device appear at PDC time?
Thans a lot,
Manuel Cotallo.
P.S. The DLT does not appear although it is already connected to HW path 10/8
#ioscan -H 10/8
ext_bus 3 10/8 c720 CLAIMED INTERFACE GSC add-on Fast/Wide SCSI Interface
target 20 10/8.7 tgt CLAIMED DEVICE
ctl 3 10/8.7.0 sctl CLAIMED DEVICE Initiator
Are any patches needed for a default install of HP-UX 11.00 in order to connect a DLT 8000 FW SCSI to a 9000/800/K380 system to "optional" connector in core I/O board, HW path 10/8?
What driver should be the suitable one? stape? tape2?
Should this device appear at PDC time?
Thans a lot,
Manuel Cotallo.
P.S. The DLT does not appear although it is already connected to HW path 10/8
#ioscan -H 10/8
ext_bus 3 10/8 c720 CLAIMED INTERFACE GSC add-on Fast/Wide SCSI Interface
target 20 10/8.7 tgt CLAIMED DEVICE
ctl 3 10/8.7.0 sctl CLAIMED DEVICE Initiator
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-28-2004 12:53 AM
тАО05-28-2004 12:53 AM
Re: Connect DLT 8000 to 9000/800/K380
Hi,
I don't think you can connect the DLT8000 to the optional connector on the core I/O of K class.
You will require an additional Card for the same.
There is a SCSI type mismatch hence your drive is not getting detected.
And
Yes For a drive to get viewed at PDC you don't require any driver.
Regards,
I don't think you can connect the DLT8000 to the optional connector on the core I/O of K class.
You will require an additional Card for the same.
There is a SCSI type mismatch hence your drive is not getting detected.
And
Yes For a drive to get viewed at PDC you don't require any driver.
Regards,
I'll sleep when i am dead.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-02-2004 01:57 AM
тАО06-02-2004 01:57 AM
Re: Connect DLT 8000 to 9000/800/K380
Hello Manuel,
you might check the answers in the following call:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=318658
In your case it looks like you have the right interface installed. You need to use the stape driver for this interface, only be sure that the DLT drive is HVD (High Voltage differential), because LVD and HVD are not compatible.
you might check the answers in the following call:
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=318658
In your case it looks like you have the right interface installed. You need to use the stape driver for this interface, only be sure that the DLT drive is HVD (High Voltage differential), because LVD and HVD are not compatible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-08-2004 07:56 PM
тАО06-08-2004 07:56 PM
Re: Connect DLT 8000 to 9000/800/K380
Manuel,
any news ?
Rgds
Alexander M. Ermes
any news ?
Rgds
Alexander M. Ermes
.. and all these memories are going to vanish like tears in the rain! final words from Rutger Hauer in "Blade Runner"
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP