- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-24-2003 10:46 PM
тАО12-24-2003 10:46 PM
DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
I have a problem to put 12/24 DAT (SDT-9000)in Disaster Recovery Mode.The drive is internal installed in Compaq Proliant 1600 Server.Can anyone tell me what is corect procedure and what are correct led indications at front of drive when it is in DR Mode?
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-25-2003 04:56 AM
тАО12-25-2003 04:56 AM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
1. Insert the SmartStart CD in your CDROM drive. Allow it to run until promted for your OS CD.
2. Remove the SmartStart CD.
3. Retrieve the most recent DRTape.
4. Make sure the DRTape is write-protected and load it into the tape drive.
5. When all 3 LED indicators are blinking, power on the computer within 15 seconds. This will place the tape drive in DR mode.
6. When the system restarts the tape drive is identified as a bootable device.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-25-2003 06:07 PM
тАО12-25-2003 06:07 PM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
I can`t understand this step:
5. When all 3 LED indicators are blinking, power on the computer within 15 seconds. This will place the tape drive in DR mode.
As I mentioned in my question my drive is internal.So the drive have power only when the computer is powered on. How I can power on the computer whitin 15 sec. when it is already running(LED indicators are blinking)???????
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-25-2003 07:06 PM
тАО12-25-2003 07:06 PM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
> As I mentioned in my question my drive is internal.So the drive have power only when the computer is powered on. How I can power on the computer whitin 15 sec. when it is already running(LED indicators are blinking)???????
Good question. I suspect you power-up the comptuer and the tape drive, and perhaps pause the boot process until the tape drive LEDs are flashing, and then resume the boot process.
I don't see the DRTape Solution reference guide available on the web, so if you send me your email address to ltt_team@hp.com, I'll email you the whole guide, in case that helps you.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2003 05:29 AM
тАО12-26-2003 05:29 AM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-26-2003 07:25 PM
тАО12-26-2003 07:25 PM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
Thank you for your efforts but I still do not have an answer how to put the Internal drive in DR Mode
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2003 03:50 AM
тАО12-27-2003 03:50 AM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
You might want to contact the hp support center - make sure you tell them it is a compaq-branded DAT drive.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-27-2003 04:13 AM
тАО12-27-2003 04:13 AM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
http://us.itrc.hp.com/service/help/siteMap.do?Page=file0901
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-28-2003 10:31 PM
тАО12-28-2003 10:31 PM
Re: DDS-3 12/24 DAT (SDT-9000) Disaster Recovery
I think you are trying to perform a DRTape Disaster Recovery and not a OBDR,
if it is the case, see:
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=PSD_EA000721_CW01
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=PSD_EX001214_CW01
to put the drive in DR mode you need first to create a DRTape (that include all the boot and config information)
then insert it in the Tape Drive, but be sure the cartridge is write protected.
When the three leds are flashing, power off the server (keep the power on button pushed for five seconds if it do not power off)
rebooting the server, the bios will discover a bootable CR-ROM instead of a Tape Drive
marino