- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: DLT Library failure
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2003 08:36 AM
тАО11-05-2003 08:36 AM
DLT Library failure
Device failure 3eh
FRU 1 27
FRU 2 40
FRU 3 43
Motion Rezero
Source 0
Destination 1 0
Destination 2 0
odometer 4554
Micromove1 16h
Micromove2 22h
Micromove3 4h
Micromove4 15h
Micromove5 33h
Micromove6 34h
ER 15h
Someone know what all this means???????
Thanks, Mark
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2003 05:12 PM
тАО11-05-2003 05:12 PM
Re: DLT Library failure
If it still fails, open a hardware call at HP for it.
Kurt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2003 08:47 PM
тАО11-05-2003 08:47 PM
Re: DLT Library failure
seem that library detected an overforce when initializing,
as suggested, power cycle it, and check also for any obstruction on the picker path
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 03:00 AM
тАО11-06-2003 03:00 AM
Re: DLT Library failure
n Look at the Micro-move error of the failure in the error log (under INFO *, and Hardware Error in the
display panel). Look at the transport assembly and vertical encoder strip to make sure that vertical positioningseems to be correct. Replace the transport assembly. Micromoveerror should be Translate over force error. Clear Hard and Softlocks an run a Wellnesstest (1 Loop) and an excersise mech test and see what Failure messages you got.
Kuifje
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 10:16 AM
тАО11-06-2003 10:16 AM
Re: DLT Library failure
The micro-moves tell us what the steps the library was taking. The last 2 are position right to end of travel which passed and position left to end of travel which failed. The error ID, 15h, says what the error was that caused the micro-move and the whole move to fail.
For this case the error is an overforce which means that the picker was trying to position to the left side end of travel and stopped before it had traveled the appropriate distance.
Possible causes of this are an obstruction which has been pointed out several time, damage to the encoder strip under the picker, or damage to the picker's translate mechanism.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-06-2003 02:05 PM
тАО11-06-2003 02:05 PM