- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- DLT V086 firmware diff
StoreEver Tape Storage
1753849
Members
8120
Online
108807
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-18-2004 04:55 AM
03-18-2004 04:55 AM
I finished upgrading a few DLT8000's yesterday to V086.
We have recieved a couple of calls today saying the front panel lights are "different".
The units I did yesterday went from V080 to V086.
Where can I find some verbage on what changes a firmware rev makes, such as the panel lights.
Thanks
Greg Heil
We have recieved a couple of calls today saying the front panel lights are "different".
The units I did yesterday went from V080 to V086.
Where can I find some verbage on what changes a firmware rev makes, such as the panel lights.
Thanks
Greg Heil
Solved! Go to Solution.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
03-18-2004 04:04 PM
03-18-2004 04:04 PM
Solution
Greg,
You are correct - the front panel behavior has some changes if tapes are left in the drive unloaded, but not removed.
Here's the particular change:
Fixed between versions V080 and V086:
Added a low power mode used while waiting for the drive handle to be opened. If after 10 minutes the handle has not been opened, the handle will lock and the holding tension on the tape will be reduced. At this point, the eject button, a SCSI unload command, or library unload command must be used to open the handle and remove the cartridge. A SCSI load command or library load command will load the cartridge and also remove the drive from the low power state.
You are correct - the front panel behavior has some changes if tapes are left in the drive unloaded, but not removed.
Here's the particular change:
Fixed between versions V080 and V086:
Added a low power mode used while waiting for the drive handle to be opened. If after 10 minutes the handle has not been opened, the handle will lock and the holding tension on the tape will be reduced. At this point, the eject button, a SCSI unload command, or library unload command must be used to open the handle and remove the cartridge. A SCSI load command or library load command will load the cartridge and also remove the drive from the low power state.
The journey IS the reward.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP