- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- EML 103 problem
StoreEver Tape Storage
1752802
Members
5775
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-06-2009 10:30 PM
09-06-2009 10:30 PM
EML 103 problem
The EML103 won't initialize:
Under the library status section we get the following error:
Library critical – one or more library components are not ready
Robotics critical – library failed to initialize
The robotics has a red light on the display and the robot does not run its course through the inventory as it should. After switch on the robot moves down then it appears to rotate then stops and remains in that position at the bottom of the library.
Here are the codes under the critical section in the error log:
Error 0100,3717 lfmInitthread :Failed to initialize reason = robot initialize failed – GOING INOP
Error 0000,0000 Director –initresponse () initialize : failed init of reach and grip
Under the Warning logs we get the following, there are a few of these
Warn,0000,3305, IFM drive event and library state is unknown
Can somebody help?
Under the library status section we get the following error:
Library critical – one or more library components are not ready
Robotics critical – library failed to initialize
The robotics has a red light on the display and the robot does not run its course through the inventory as it should. After switch on the robot moves down then it appears to rotate then stops and remains in that position at the bottom of the library.
Here are the codes under the critical section in the error log:
Error 0100,3717 lfmInitthread :Failed to initialize reason = robot initialize failed – GOING INOP
Error 0000,0000 Director –initresponse () initialize : failed init of reach and grip
Under the Warning logs we get the following, there are a few of these
Warn,0000,3305, IFM drive event and library state is unknown
Can somebody help?
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-22-2009 01:30 PM
09-22-2009 01:30 PM
Re: EML 103 problem
Hi Richard,
I have a few questions about the issue:
- If you open the front door, is there anything obstructing the Robot's movement like a media around or so?
- Which is the correct firmware version?
- Library Controller has a red LED?
I have a few questions about the issue:
- If you open the front door, is there anything obstructing the Robot's movement like a media around or so?
- Which is the correct firmware version?
- Library Controller has a red LED?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-22-2009 10:29 PM
09-22-2009 10:29 PM
Re: EML 103 problem
We just found out that the flatcable connected to the robot was damaged. Ordered a new one, so problem is solved. Thank you.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP