- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Firmware Colorado 20Gb
StoreEver Tape Storage
1753336
Members
4789
Online
108792
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-21-2002 06:41 PM
09-21-2002 06:41 PM
Re: Firmware Colorado 20Gb
Folks:
I am having the same problem (need to update my firmware), but I have the additional problem that WinXP sees the tape drive in device manager, but does not show it using resources (ie IRQ or I/O address), so I cannot get the DOS boot disk to work. Any ideas on how to get the IRQ and I/O the drive is using? The tape is the secondary IDE slave device, if that helps.
I am having the same problem (need to update my firmware), but I have the additional problem that WinXP sees the tape drive in device manager, but does not show it using resources (ie IRQ or I/O address), so I cannot get the DOS boot disk to work. Any ideas on how to get the IRQ and I/O the drive is using? The tape is the secondary IDE slave device, if that helps.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-21-2002 08:07 PM
09-21-2002 08:07 PM
Re: Firmware Colorado 20Gb
Folks:
I figured out the DOS firmware problem, my device is on the primary IDE chain, so I just had to change the address and IRQ in the .ini file to get it to work. I flashed the firmware, but I still get the same error message - 05-0E-23-01-0524, when I try to use Backup MyPC or Colorado b/u v9.1. This is supposed to be a firmware problem, but I have the latest f/w. Any ideas? Thanks in advance.
I figured out the DOS firmware problem, my device is on the primary IDE chain, so I just had to change the address and IRQ in the .ini file to get it to work. I flashed the firmware, but I still get the same error message - 05-0E-23-01-0524, when I try to use Backup MyPC or Colorado b/u v9.1. This is supposed to be a firmware problem, but I have the latest f/w. Any ideas? Thanks in advance.
- « Previous
-
- 1
- 2
- Next »
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP