- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- HP 418 Autoloader - changer is not recognized
StoreEver Tape Storage
1754020
Members
6894
Online
108811
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-04-2004 11:24 PM
02-04-2004 11:24 PM
HP 418 Autoloader - changer is not recognized
The drive is being recognized; however, the chnager is not. During the server boot up I see the drive, but nothing about the changer. We also have an HP 2/20 Library that shows both the drive and changer listed during server boot up. The same with LTT.
I'm using an Adpaptec 39160 SCSI card and BackUp Exec 9.1 for my backup software. I've changed SCSI ID's to 4 for the drive and 3 for the autoloader but that didn't change anything. I also changed the INQ_TOGGLE to ON.
It was all working fine on a different server, but it crashed and we now have a new Dell server. The main difference is the SCSI card. The old server had it built into the motherboard and we bought the Adaptec 39160 card with the new server.
In Windows Event Viewer I get the following message. 'The HPDLT628 service depends on the SCSI-2 Medium Changer group and no member of this group started.'
I would appreciate any help.
Scott
I'm using an Adpaptec 39160 SCSI card and BackUp Exec 9.1 for my backup software. I've changed SCSI ID's to 4 for the drive and 3 for the autoloader but that didn't change anything. I also changed the INQ_TOGGLE to ON.
It was all working fine on a different server, but it crashed and we now have a new Dell server. The main difference is the SCSI card. The old server had it built into the motherboard and we bought the Adaptec 39160 card with the new server.
In Windows Event Viewer I get the following message. 'The HPDLT628 service depends on the SCSI-2 Medium Changer group and no member of this group started.'
I would appreciate any help.
Scott
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
02-11-2004 01:47 AM
02-11-2004 01:47 AM
Re: HP 418 Autoloader - changer is not recognized
Hi Scott,
from the sound of it you may have 1 of these issues....
First it would be worth checking if the flat metal jumper cable that connects the drive and robot at the back of the AL might possably be defect, this can be checked by connecting the long data-cable and the terminator to the robot and after that to the drive only.
If u then can see the robot on the scsi bus, then the jumpercable needs replacing !! part no = C6280-60070
besides that there is a second possabillity. u may not have configured or installed the correct tape / scsi driver and/or autoloader - option for the 418.
http://seer.support.veritas.com/docs/251466.htm
AND http://www.adaptec.com/worldwide/support/suppbyproduct.html?sess=no&language=English+US&cat=/Technology/SCSI+Host+Adapters&fromPage=driverindex for the latest drivers.
And last but not least as the unit is a single-ended narrow scsi2 pls ensure correct cabling and termination !!
The unit - if correctly connected - set to SE speed on that channel + terminated with active terminator should work fine with buexec.
If u check the AL with LTT diag sw for latest firmware, u should have no more issues. diagsw and info avaliable on:
http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?locale=en_US&prodTypeId=12169&prodSeriesId=63825&submit.y=8&submit.x=9〈=en&cc=us
hope this answers your question why :)
@>'-;--- tk
p.s. your 2/20 is LVD the 418 = SE
from the sound of it you may have 1 of these issues....
First it would be worth checking if the flat metal jumper cable that connects the drive and robot at the back of the AL might possably be defect, this can be checked by connecting the long data-cable and the terminator to the robot and after that to the drive only.
If u then can see the robot on the scsi bus, then the jumpercable needs replacing !! part no = C6280-60070
besides that there is a second possabillity. u may not have configured or installed the correct tape / scsi driver and/or autoloader - option for the 418.
http://seer.support.veritas.com/docs/251466.htm
AND http://www.adaptec.com/worldwide/support/suppbyproduct.html?sess=no&language=English+US&cat=/Technology/SCSI+Host+Adapters&fromPage=driverindex for the latest drivers.
And last but not least as the unit is a single-ended narrow scsi2 pls ensure correct cabling and termination !!
The unit - if correctly connected - set to SE speed on that channel + terminated with active terminator should work fine with buexec.
If u check the AL with LTT diag sw for latest firmware, u should have no more issues. diagsw and info avaliable on:
http://h20000.www2.hp.com/bizsupport/TechSupport/Home.jsp?locale=en_US&prodTypeId=12169&prodSeriesId=63825&submit.y=8&submit.x=9〈=en&cc=us
hope this answers your question why :)
@>'-;--- tk
p.s. your 2/20 is LVD the 418 = SE
If U want to; let's get technical.... :P
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP