- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL 2040 Tape Libary error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2007 02:47 AM
тАО02-06-2007 02:47 AM
When i start the tape library it gives error:
Comm. Error.
Code F1 00
What could be the cause??
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2007 04:13 AM
тАО02-07-2007 04:13 AM
Re: MSL 2040 Tape Libary error
Can you clear the error and continue to use the library?
There have been a few reports of an F1/00 errors occuring in normal operation and we are working on identifying the cause and a solution. None of the errors we have seen so far have caused any operational problems.
If the problem is fequent and causes operational problems then it is a different issue. The only case I have seen where this problem occurred fequently was with an incorrectly assembled drive can. The communication cable to the drive was not fully seated.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2007 05:21 PM
тАО02-07-2007 05:21 PM
Re: MSL 2040 Tape Libary error
Thanks for you reply.
Sorry i didn't explain the issue properly.To tell u exactly, we are still to use that device.I did the EVA installation and The Tape library is a part of it.When i started the device for the first time to configure it with SAN switch, i saw this error on OCP. I didn't even get the WWN number on the SAN switch. (The FCP ports are located on the back of the Drive of MSL 2024)
I tried to reseat the drive but the error is still there.
I think that the drive is not connected properly with the Tape library, because if it is just and operational error then atleast i would have got the WWN number of the library on the SAN switch. I changed the FCP port settings of the drive to auto/fibre but no change.
Even i tried to cancel the error but it does not goes of. If i do any operation on tape library it fails.
Any operation which has only to do with Library is working fine like left/right cartridge eject. But when it has something to do with the drive it fails. And error never goes off. Even when i reboot the drive it shows no error untill it displays Move on OCP and pops up the errorwhich never goes after that.
Is there any hardware issue??
Is my device dead on arrival??
It would be a great help if you can give your views about this issue ASAP.
Thanks!!!!!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-07-2007 05:24 PM
тАО02-07-2007 05:24 PM
Re: MSL 2040 Tape Libary error
Thanks!!!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-08-2007 04:22 AM
тАО02-08-2007 04:22 AM
SolutionIt looks like the library is completely unable to communicate with the drive. The drives are tested before leaving the factory but it sounds like this one isn't turning on now for some reason.
Either the cables in the back of the drive can weren't installed correctly and have come loose or the drive itself has failed. Either way the repair part is a new drive assembly.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2007 07:25 PM
тАО02-09-2007 07:25 PM
Re: MSL 2040 Tape Libary error
Thanks for your reply.
Your suggestion hepled alot. We are looking for warrenty claim.
I really appreciate your help.
Thanks again
Rakesh
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-09-2007 07:29 PM
тАО02-09-2007 07:29 PM