- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL 5052 S2
StoreEver Tape Storage
1753929
Members
9114
Online
108810
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2007 05:08 AM
тАО01-18-2007 05:08 AM
MSL 5052 S2
I have a MSL5052 S2 robot attached via SAN. I have a HP DL580 server also attached to the SAN runing Win 2003 Ent Svr and Backup Exec for Windows. For some reason the server does not see the tape drive any longer. The NSR says the changer is up as well as both tape drives. I attempted to re-install the Symantec device drivers but no success.
Any help would be appreciated.
Any help would be appreciated.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2007 12:46 AM
тАО01-19-2007 12:46 AM
Re: MSL 5052 S2
Hello Paul - sounds like a mapping problem on the NSR, or maybe zoning ? - I'm not sure if you've lost the entire library, or just one drive
First make sure the NSR fibre port, and the DL580 HBA(s) can talk to each other - try connecting to the switch(es) and ensure they are both fully logged-in, and have an entry in the nameserver table. Make sure that the zoning allows them to "see" each other.
If this is OK - check the mapping on the NSR.
If you've not done this before, it can get complicated (depending on your site's configuration). At least one HBA WWID on your DL580 should be listed on the left-hand section of the NSR "mapping" GUI screen. Is it possible that the NSR has been "factory defaulted", or replaced ? - in which case the mappings will have been lost.
If its just one drive you've lost - it could also be a mapping problem, or it could be that Backup Exec has lost visibility. Backup Exec "tracks" drive serial numbers, so if the drive has been replaced, you will need to re-add it from the "devices" screen. An easy way to check for this is to see if the W2K3 Device Manager has all the drives listed. If it has, then it's most probably a Backup Exec issue.
If you think it may be a mapping issue - post the NSR mapping screen display.
Hope this helps
First make sure the NSR fibre port, and the DL580 HBA(s) can talk to each other - try connecting to the switch(es) and ensure they are both fully logged-in, and have an entry in the nameserver table. Make sure that the zoning allows them to "see" each other.
If this is OK - check the mapping on the NSR.
If you've not done this before, it can get complicated (depending on your site's configuration). At least one HBA WWID on your DL580 should be listed on the left-hand section of the NSR "mapping" GUI screen. Is it possible that the NSR has been "factory defaulted", or replaced ? - in which case the mappings will have been lost.
If its just one drive you've lost - it could also be a mapping problem, or it could be that Backup Exec has lost visibility. Backup Exec "tracks" drive serial numbers, so if the drive has been replaced, you will need to re-add it from the "devices" screen. An easy way to check for this is to see if the W2K3 Device Manager has all the drives listed. If it has, then it's most probably a Backup Exec issue.
If you think it may be a mapping issue - post the NSR mapping screen display.
Hope this helps
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-19-2007 02:11 AM
тАО01-19-2007 02:11 AM
Re: MSL 5052 S2
Rich,
Thanks for the reply. I think you are on to something. Right now, under Device Manager, the server does not list a medium changer or a tape drive. I will look at the NSR mapping forum.
Thanks,
Paul
Thanks for the reply. I think you are on to something. Right now, under Device Manager, the server does not list a medium changer or a tape drive. I will look at the NSR mapping forum.
Thanks,
Paul
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP