- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: MSL6000 + BL460C
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-12-2007 04:36 AM
тАО03-12-2007 04:36 AM
MSL6000 + BL460C
I have MSL6000 + BL460C server
I connected MSL fibre port with blade san switch.but no connectivity is showing in any blade server.
kindly any one help me in this regard
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-12-2007 04:55 AM
тАО03-12-2007 04:55 AM
Re: MSL6000 + BL460C
you need to log into the NSR and configure the port, you can do that by using the rj11 port on the NSR, connaect using a hyper terminal.
If it is already configured to be used with a web browser, you need to go and check the the port spped is the corrct one, and that the rest of the settings (SAN) are correct.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-12-2007 04:59 AM
тАО03-12-2007 04:59 AM
Re: MSL6000 + BL460C
http://h20000.www2.hp.com/bizsupport/TechSupport/SupportTaskIndex.jsp?lang=en&cc=us&prodTypeId=12169&prodSeriesId=316040&taskId=115
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2007 02:12 AM
тАО03-13-2007 02:12 AM
Re: MSL6000 + BL460C
Thanks...
I followed this document. I did following acgtions on NSR but didnt get any result.
1) I tried with Serial port communication with RS232 port and serail port.
I tried all options with 19200,9600 etc.
It doesnt show any comunication.
2) Tried to communicate with 10BaseT with 1.1.1.1 port and didnt get any result.
It doesnt even ping 1.1.1.1
3) I tried plug in cross over cable one end at my laptop and one end directly on 10BaseT port but didnt get any result.
Do u think there might be any hardware failure on NSR card
kindly help me ....
Thanks
again
Zubair Alam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2007 02:27 AM
тАО03-13-2007 02:27 AM
Re: MSL6000 + BL460C
I can send you an NSR1200 Manual if you would like to try and diag the problem.
Its size is 4M so i would need an FTP site to upload it to.
Tal
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2007 02:35 AM
тАО03-13-2007 02:35 AM
Re: MSL6000 + BL460C
Some of the basic factory default values are:
├в IP address: http://1.1.1.1/
├в Subnet mask: 255.255.255.0
├в Gateway address: 0.0.0.0
├в User name: root
├в Password: password
To open a serial session, a terminal emulator utility is required.From most Windows 9x, Windows NT, and Windows 2000 systems, a HyperTerminal session can be started using the following steps:
1.From the Windows Start Menu, open HyperTerminal.
2.Name the new terminal session.
3.Indicate the appropriate COM port.
4.Configure the serial port settings, as listed in Table├В 7.Note: HP recommends setting the baud rate to 115200.
5.After completing the serial port configuration, select OK to start a serial session.
6.After the serial session has started, press Enter several times to initiate router communication and display the Configuration Menu.Table 7: Terminal Configuration SettingsBAUD Rate Autobaud, 9600, 19200, 38400, 57600, 115200
Data Bits 8
Stop Bit 1
Parity None
Flow Control XON/XOFF
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2007 03:09 AM
тАО03-13-2007 03:09 AM
Re: MSL6000 + BL460C
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-13-2007 08:16 PM
тАО03-13-2007 08:16 PM
Re: MSL6000 + BL460C
Yes Taal I tested with serial connections
( by following exactly procedure which u mentioned me...with using all baud rate ) i waited several minutes to get any connections but i didnt get any result . I also tried with ip 1.1.1.1 but no result.
i would be thankful to you u could email me NSR1200 manual at my email add zubairalam@jaffer.com
Best Regards
Zubair Alam
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-14-2007 12:56 AM
тАО03-14-2007 12:56 AM
Re: MSL6000 + BL460C
Tal