- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL6000 NSR reconfigurations
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2008 12:48 PM
тАО01-04-2008 12:48 PM
MSL6000 NSR reconfigurations
I would like somewhat detailed guidance on NSR reconfiguration. Below is the current configurations.
- NSR is connected to the same fabric switch as the two NEW HP-UX hosts it is going to back up.
- Fabric zoning is done. Both HP-UX hosts can see the two drives on MSL6000.
- The robotic arm (autochanger) cannot be seen yet on either host.
In brief, I would like to be able to reconfigure the NSR in order for the two HP-UX hosts to see the robotic arm. Thanks.
Hai
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-04-2008 01:18 PM
тАО01-04-2008 01:18 PM
Re: MSL6000 NSR reconfigurations
Check: http://h10032.www1.hp.com/ctg/Manual/lpg29075.pdf
Page 65
Check this page on how to do the mapping:
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&taskId=120&prodSeriesId=337412&prodTypeId=12169&objectID=c00539218
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-05-2008 05:08 AM
тАО01-05-2008 05:08 AM
Re: MSL6000 NSR reconfigurations
You might also want to check that the SCSI cabling is correct. It's common to see the library controller, not connected to the NSR which would give the problem you're seeing...
SCSI port 0 on the NSR should go to the library controller card, and then on to drive 0.
SCSI port 1 on the NSR should go to drive 1.
Hope this helps,
Regards,
Rob
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2008 11:12 AM
тАО01-06-2008 11:12 AM
Re: MSL6000 NSR reconfigurations
If you see something like this:
unknown -1 1/0/4/0/0.5.10.255.0.0.0 UNCLAIMED UNKNOWN HP
MSL6000 Series
the schgr driver is missing.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2008 01:17 PM
тАО01-07-2008 01:17 PM
Re: MSL6000 NSR reconfigurations
Hai
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-08-2008 09:42 AM
тАО01-08-2008 09:42 AM
Re: MSL6000 NSR reconfigurations
- The WWN of the HBA on the server appears on the NSR list
- That WWN has a mapping assigned
- That mapping contains the library controller
- The order of the devices on the map depends on the OS of the server, it's different for Windows and HP-UX for example.