- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: MSL6000 front panel msg: "Magazine type change...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 06:17 AM
тАО06-06-2006 06:17 AM
MSL6000 front panel msg: "Magazine type changed"
"Some of the inserted magazines (lower right) are of a different type than the ones removed.
Leaving these magazines in the library will cause its geometry to change.
Press OK to reconfigure and reboot, press CANCEL to replace magazine."
We only have 4 magazines- the four that came with the library- and they all look the same to me...
Here's how it usually goes:
>Check libray in the afternoon before going home, no panel message, all is well.
>Come in the next morning to find that some overnight backup tapes failed. DataProtector log shows "Cannot open exchanger control device (Unit is not ready.)"
>Check MSL6000 front panel, get "Magazine type changed" message.
Now today the message popped up in the middle of the afternoon. Everything worked fine this morning, andwe haven't touched the library in 5 hours, but the message is there.
Any ideas?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 07:03 AM
тАО06-06-2006 07:03 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 07:12 AM
тАО06-06-2006 07:12 AM
Re: MSL6000 front panel msg: "Magazine type changed"
The message has been popping up from time to time for over a month now, both before and after the firmware update.
Any idea how the machine senses the magazine type? Far as I can tell, the magazine doesn't have a barcode or any identifying marks on it...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 07:26 AM
тАО06-06-2006 07:26 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 07:33 AM
тАО06-06-2006 07:33 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-06-2006 09:14 AM
тАО06-06-2006 09:14 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Points are always welcome in the forums.
;-))
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-07-2006 03:08 AM
тАО06-07-2006 03:08 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Thanks.
More to come...
Points have been assigned (I think - new here).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-10-2006 03:14 AM
тАО06-10-2006 03:14 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Hardware: MSL 5026S2 (SDLT Lib)
I have similar problem, I have updated the firmware of Library to v.5.13 but problem repeated after two weeks that left side magazine type changed to LTO instead of DLT.
I have already replaced the control panel board. Still problem repeated after two weeks.Currently I have disconnect the LTO sensor connection from control panel board.
I don't suspect sensor bcoz, whenenver I disconnect the LTO sensor it sens magazine as DLT, after I connect back it still shows DLT for some time. after two weeks problem repeats.
Can any assist on this issue?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2006 07:23 AM
тАО06-14-2006 07:23 AM
Re: MSL6000 front panel msg: "Magazine type changed"
So that should do it, but time will tell...
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-14-2006 09:03 AM
тАО06-14-2006 09:03 AM
Re: MSL6000 front panel msg: "Magazine type changed"
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!