- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: SCSI termination not found
StoreEver Tape Storage
1748272
Members
4214
Online
108760
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-29-2004 06:26 PM
тАО04-29-2004 06:26 PM
SCSI termination not found
during boot after the press ctrl-a line comes a message:
29160LP A at slot 01, 00:02:00 - SCSI termination not fond
and the system hangs.
conds are: ibm xseries 335 with aditional 29160 adapter, connected to external DAT24 with terminator.
all terminators tested bring the same result.
without terminator the controller bios recognizes C1537A, the system boots, and tar brings no errors.
can anyone give a declaration of this behavior,
and if possible a hint, what must be done
that the dat24 drive works as described in docu?
tnx in advance, bernd salzmann.
29160LP A at slot 01, 00:02:00 - SCSI termination not fond
and the system hangs.
conds are: ibm xseries 335 with aditional 29160 adapter, connected to external DAT24 with terminator.
all terminators tested bring the same result.
without terminator the controller bios recognizes C1537A, the system boots, and tar brings no errors.
can anyone give a declaration of this behavior,
and if possible a hint, what must be done
that the dat24 drive works as described in docu?
tnx in advance, bernd salzmann.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2004 03:12 AM
тАО04-30-2004 03:12 AM
Re: SCSI termination not found
hi
29160LP have anexternal connector 68 pin HD or VHD (do not remember well) and is a Wide bus (16 bits) LVD
DAT 24 is a Single Ended with Narrow bus (8 Bits)
The problem is that if you connnect such a device to the 68 bits, you terminate only the first 8 bits of the bus, leaving the higher part disconnected. in this case the HBA saw that there is some kind of error on the bus and show you the error.
In order to work you need to attach a special cable (if it exist for VHD, I know it exist for HD) with higher bits terminated, so that you can attact the Narrow device on the lowest bits and attach the terminator on the external DAT.
Also, you need a SE terminator or a LVD/SE multimode terminator for this device
29160LP have anexternal connector 68 pin HD or VHD (do not remember well) and is a Wide bus (16 bits) LVD
DAT 24 is a Single Ended with Narrow bus (8 Bits)
The problem is that if you connnect such a device to the 68 bits, you terminate only the first 8 bits of the bus, leaving the higher part disconnected. in this case the HBA saw that there is some kind of error on the bus and show you the error.
In order to work you need to attach a special cable (if it exist for VHD, I know it exist for HD) with higher bits terminated, so that you can attact the Narrow device on the lowest bits and attach the terminator on the external DAT.
Also, you need a SE terminator or a LVD/SE multimode terminator for this device
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО04-30-2004 03:14 AM
тАО04-30-2004 03:14 AM
Re: SCSI termination not found
I forgot,
If you can found an old Adaptec 2940, it may be cheaper than the special cable, and would support the DAT 24 with narrow bus and SE mode
If you can found an old Adaptec 2940, it may be cheaper than the special cable, and would support the DAT 24 with narrow bus and SE mode
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP