- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- TL891 SCSI settings
StoreEver Tape Storage
1753519
Members
5709
Online
108795
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2006 06:48 AM
01-11-2006 06:48 AM
TL891 SCSI settings
I have a TL891 minilibrary (firmware 5.25)and would like to know how to set the SCSI ID settings for the single 35/70 Gb drive in the library. I have already set the SCSI ID for the robotic library to SCSI ID 2 and Windows recognizes the robotic library but not the drive. Any suggestions on how to get Windows to recognize the drive will be greatly appreciated.
PS. The robotic library recently displayed fault code 2072 and I had to reset the storage unit to the factory defaults to clear the error message. I now need to know how to change the robotic library configuration settings for Windows to recognize the tape drive.
Thanks,
Glen Pappas
IT Network Administrator
PS. The robotic library recently displayed fault code 2072 and I had to reset the storage unit to the factory defaults to clear the error message. I now need to know how to change the robotic library configuration settings for Windows to recognize the tape drive.
Thanks,
Glen Pappas
IT Network Administrator
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2006 09:12 PM
01-11-2006 09:12 PM
Re: TL891 SCSI settings
The SCSI ID can be set Under Configure Menu by going into Set SCSI
As you said you did a reset to clear the 2072 error,the drive should have disappeared after that.Are you able to see the drive once the TL891 initalizes and shows the status on the front panel.If the Drive is not getting detected,you may check refixing the Drive's internal cable to see if it helps
As you said you did a reset to clear the 2072 error,the drive should have disappeared after that.Are you able to see the drive once the TL891 initalizes and shows the status on the front panel.If the Drive is not getting detected,you may check refixing the Drive's internal cable to see if it helps
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP