- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- URGENT: MSL6030 with e1200-320 4Gb FC Interface Ca...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 05:48 PM
тАО06-13-2007 05:48 PM
URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
We are deploying MSCE cluster based on ProLiant BL460c blades. I have to connect MSL6030 library to one of the cluster nodes via Brocade BladeSystem 4/12 SAN switch. Zoning is switched on.
First of all, i logged into e1200-320 card using visual interface and changed configuration of the card FC port (from loop to switched fabric). Then i logged into switch console, checked out if i could see WWN of the card, and created new zone.
After all, i logged into e1200-320 card once again. The link is up, but on Discovery screen i see "There are no devices attached to this port at this time" under "FC Port 0 Devices" string. No devices were found on target host also even after reboot of the host.
I checked out Mapping Menu, and there was no host listed. Should i manually add host WWN to map drives on the host or I made a mistake somewere else?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 06:02 PM
тАО06-13-2007 06:02 PM
Re: URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
This config "maps" the SCSI devices to the SAN.
No mapping = no devices visible on the SAN.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 06:50 PM
тАО06-13-2007 06:50 PM
Re: URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
I tried to config mapping actually, but there is no host infomation automatically propogated on the mappings page. It's only possible to enter host information manually.
I suppose, that something wrong with zone config. Hitachi AMS500 disk array is connected to the cluster through SAN, too. So I configured 2 separate zones for the node we plan to use as backup serve - one zone for storage and one zone for MSL FC card. Is that correct?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 06:56 PM
тАО06-13-2007 06:56 PM
Re: URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 07:08 PM
тАО06-13-2007 07:08 PM
Re: URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
As far as i understood, until i get the correct host infomation displayed on the mappings menu, i can't go any further?
Another question is, what kind of map type should i use - "Auto Assigned" or "Indexed"(set by default), and what are the differences between them?
Thanks, Denis.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2007 07:44 PM
тАО06-13-2007 07:44 PM
Re: URGENT: MSL6030 with e1200-320 4Gb FC Interface Card - help needed
http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=SupportManualтМй=en&cc=us&docIndexId=179111&taskId=101&prodTypeId=329290&prodSeriesId=1849252
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!