- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- dat24x6 autoloader: display during write.
StoreEver Tape Storage
1752799
Members
6177
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-11-2008 08:00 AM
07-11-2008 08:00 AM
dat24x6 autoloader: display during write.
During writes, there is a decimal number to the right, something like "Write 1.1". I've seen that number be anything from 0.9 to 1.5.
Can anyone tell me what that number is measuring?
Can it give me any useful information about the tape, or the drive, etc...
Thanks.
- Scott
Can anyone tell me what that number is measuring?
Can it give me any useful information about the tape, or the drive, etc...
Thanks.
- Scott
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-12-2008 10:24 PM
07-12-2008 10:24 PM
Re: dat24x6 autoloader: display during write.
Hi Scott,
check this link http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=lpg50043
Write x.y S The drive is writing data to tape. "x.y:1" is the cumulative compression ratio since power on, or since the compression ratio was last cleared. For example, "Write 2.1" means a compression ratio of 2.1:1. The compression ratio is only displayed after about 1 MB of data has been written since power on.
Let me know if have further questions
Regards
check this link http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=lpg50043
Write x.y S The drive is writing data to tape. "x.y:1" is the cumulative compression ratio since power on, or since the compression ratio was last cleared. For example, "Write 2.1" means a compression ratio of 2.1:1. The compression ratio is only displayed after about 1 MB of data has been written since power on.
Let me know if have further questions
Regards
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP