- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: e1200 hardware reset?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2004 11:17 PM
тАО08-31-2004 11:17 PM
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2004 11:32 PM
тАО08-31-2004 11:32 PM
Re: e1200 hardware reset?
Can you log on to the NSR using the web interface? You can restore the factory default settings in there:
System:
Reset Menu
This can be done from the CLI (telnet or serial connection) as well:
Configuration Menu:
C) Reset and Save Configuration to factory defaults.
But just start by powering off and on again the NSR. See if you can access it again now.
best regards,
Kurt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2004 11:46 PM
тАО08-31-2004 11:46 PM
Re: e1200 hardware reset?
I'm giving the serial connection a go - Do you know the default hyperterminal settings? Parity, Stop bits, Data bits?
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-31-2004 11:50 PM
тАО08-31-2004 11:50 PM
Solution*BAUD rate: Autobaud, 9600, 19200, 38400, 57600, 115200
*Data bits: 8
*Stop bits: 1
*Parity: None
*Flow control: XON/XOFF
If you try to connect to 1.1.1.1, make sure you've got a local IP address in the same subnet (eg 1.1.1.2).
hth,
Kurt
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2004 12:44 AM
тАО09-01-2004 12:44 AM
Re: e1200 hardware reset?
Many thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-01-2004 12:45 AM
тАО09-01-2004 12:45 AM