- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- how to change a drive scsi id of 10/180 library?
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-25-2007 07:43 PM
тАО10-25-2007 07:43 PM
how to change a drive scsi id of 10/180 library?
i have do some configuration on a 10/180 library, and now i could not ioscan drive 0, which is on the same scsi path with the robot, and this path is linked to port 0 of the scsi-fibre switch, and drive 1 is linked to port 1 of the scsi-fibre switch. now in ioscan output, i could read the robot, whose id is 0, and drive 1, whose id is 1, but no drive. can i just change the scsi of all these three parts? their id used to be 0 for drive 0, 1 for robot and 2 for drive 1, which i recalled. or is there problem with drive 0?
thanks a lot
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-25-2007 08:09 PM
тАО10-25-2007 08:09 PM
Re: how to change a drive scsi id of 10/180 library?
http://forums1.itrc.hp.com/service/forums/questionanswer.do?threadId=1172135
Did you swap the drives or not?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-25-2007 08:39 PM
тАО10-25-2007 08:39 PM
Re: how to change a drive scsi id of 10/180 library?
i swap drive 0 and drive 1, and caused the problem above, so i set scsi id at front panel, and this time, ioscan is ok, i can read all 8 drives and the robot, and 7 of them are ok, except drive 0, when i unload the tape, i said again: device busy. it seems that it was not a drive hardware problem(cause i have swap drive 0 and drive 1). so what could it be?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-25-2007 11:29 PM
тАО10-25-2007 11:29 PM
Re: how to change a drive scsi id of 10/180 library?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-26-2007 03:23 AM
тАО10-26-2007 03:23 AM
Re: how to change a drive scsi id of 10/180 library?
there is no application that hanging to make the drive 0 busy, i think it was caused by mass of scsi changing.